The system battery was low and I replaced it. The system status continues to say that the battery is low.

hi, how many times does it flash then a pause then start flashing again ? if it a continuous flash with no pause , normally means low battery .

Regards
Rob

a continuous green flashing status light with no pause means battery voltage low , if there is a pause count how many flashes before a pause, the controller telling you what the fault is ..

Regards
Rob

Check that you are not using an app that is continuously accessing the internet and communicating with a server for some reason that is using the phones WiFi or mobile channel. This will drain battery life if incorrectly configured etc ( i.e selecting access to your location, services and other info )

Stanley 300 amp jump-start system status lights don't work. only low stays on

Did you run sensor test(drop down cover enter you code pess test button then done button. let run 5 min. close cover press status button If that fixes great. If not, you need multi meter. remove battery put metter on leeds coming off panel. You should see voltage there at least equal to the battery. If not then you may see the the red wire for battery has a lump in it about 1" long that is a fuse. remove wire from panel and meter for resistance/continuity/ohms what ever you want to call it. if there is no resistance or an open ckt then replace that wire.if you see resistance in wire then you have a bad panel. GL.

disconnect battery put dc meter on wires. should read over 6v if not need new panel. if over 6v put system in sensor test wait 5min then close cover hit status 2 times. if reset great. if not try another battery. repeat sensor test. if resets great if not need new panel. : (

NOTE: Battery operating time (the time the battery can hold a charge) decreases over time. Depending on how often the battery is used and the conditions under which it is used, you may need to purchase a new battery during the life of your computer. Check the battery status light — If the battery status light flashes orange or is a steady orange the battery charge is low or depleted. Connect the computer to an electrical outlet.
If the battery status light flashes green and orange, the battery is too hot to charge. Shut down the computer, disconnect the computer from the electrical outlet, and then let the battery and computer cool to room temperature.
If the battery status light rapidly flashes orange, the battery may be defective. Contact Dell _I found this on : http://support.dell.com/support/edocs/systems/latd820/en/ug/index.htm Hope this helps and good luck. if i "fixed ya" please rate me. thanks-jmattes

You must unplug the transformer to the system before installing the new battery so the system recognizes that the battery is in place. Once you have installed the battery it is safe to plug the transformer back in.

Here is the troubleshooting guide for your unit. Hope this helps.

TROUBLE SHOOTING GUIDE
TROUBLESHOOTING
Symptom Remedy
1. Remote does not turn on system
- Check and replace remote batteries if the display fades while
any button is activated or no display is present. - Point remote towards IR receiver during transmission. 2. System does not turn on, no green LED & no beep
- Check wiring. (see "installation instruction")
- Check modular cable to receiver.
- Check diagnostic LED status in the upper unit control box.
3. System does not turn on even when receiver green LED is on.
- Low or over voltage condition, check diagnostic LED status in the upper unit control box.

4. Fan runs but no cold air.
- Evaporator temperature sensor reaches low limit, defrost mode.
- Check diagnostic LED status in the upper unit control box.
5. System runs continuously in the cool mode
- Remote was set for "I feel" mode and is left in a heated environment (sun etc.)
6. System runs continuously in the heat mode
- Remote was set for "I feel" mode and is left in a cool environment

1. Diagnostic LED (green)
(Note: Located on the control board in the upper unit control box.)
a) The LED is on when the 12VDC is adequate and communications are
present.
b) The LED is flashing fast and steady when in the freeze mode. Evaporator has frozen and the freeze proctection switch is engaged.
c) The LED is flashing slow and steady when the delay on break timer is
activated.
d) The LED is flashing 1 cycle on and off for one second with high or low
12VDC. Check the incoming 12VDC power for OK.
e) The LED is flashing 2 cycles on and off for one second with a
communication problem. Problem with the control board in the unit and the remote.

Hope this helps.

Jeff

Rate me Please!!!

I install these panels.  For the low battery message to clear you need to power the system down completely.  To do this you need to unplug the battery and also unplug the transformer plugged into an electrical outlet.  When you power the system back up, you need to first plug in the battery leads.  Then the transformer.