No power, already max the battery to full, held the battery in push position. Just stopped working

what is it, ?
2013 made, M means mobile
black screens , Asus logo dead, screen dead black ,BIOS dead. login dead, with power button held for 10 full seconds. ok?

sure it is dead are not all that old dead, for all this classic reasons due to ITS AGE.
1-the big huge battery is bad, remove it run on AC power pack only even forever. battery here can short and overload power.

2: coin cell battery inside dead, as all are this old. replace it.
7 year max and is close to end of life.
3; HDD dead, as most are this old (unless parked as a hanger queen unused for decade) we run smart tests on it.
4: CCFL lamps behind LCD DEAD> not your PCl. yours is LED good.,

so do the long reset first, big battery out , AC pulled
push power for 30 seconds, release
put back AC pack only , and see that BIOS works
report if the all BIOS hot keywork next with SCREENS BIOS all working, this is first step on all PC made this.
(not apple bs)
The bios most work even with HDD removed.
remove all USB toys first.

If you had a short in the starter motor windings and held the key, you'd get a click and a burning smell. That would be the insulation burning off the electrical windings. There's a 40-amp max fuse in this circuit.

Take care. First put the volume down complete. Then unplug the head phone and than try to raise the volume. Could be the headphone connector does not switch through correct. Could be the connections between the pre and power amp are not in place or not proper pushed in?
Always take care when working with amplifiers. When switching them on with volume to max, you easy can kill your speakers. Also when disconnecting the headphones on full power kan damage the loudspeakers.

same like you need to change the wiper plade and the new one wipe the blade with some oil

I had come home about a week ago and pushed the power button from my remote but my tv did not respond. So I just went to the front panel and pushed power but once the tv turned on, the volume was on full blast! I used the front panel volume decrease to get the volume down, but when I stopped pushing the button, the tv increased its volume to full blast again by itself! Naturally I just turned the tv off for a few moments. I tried the remote again, no response again, so I used the panel power button. The tv volume was still full blast when it turned on but after I decreased the volume it stayed this time. The picture is and has been perfectly fine and the tv was working fine. The next day the problem started all over and now once we turned it off from frustration of having to manually use the panel to change channels, it now will not turn on at all. I have changed batteries from my remote, reprogrammed my remote, pushed system reset several times, unplugged it for a while, bought a new surge charge, and even held the menu and device panel buttons for 10 sec and tried to turn the t.v. on again! What other options do I have or what may be the issue at hand and possible parts that may need to be replaced?? Thanks!!

If the light on the remote is not lighting when you push a button, check the batteries to make sure they are in the proper position. If one is turned the wrong way, the hand held will not work. You may also want to check the replacement batteries to make sure they are fully charged. If all this fails to solve the problem, you will need replace the hand held remote. Since Hampton Bay Fans are a house brand for Home Depot, they stock and sell replacement hand held remote controls.

Hope this helped you. Please let me know. Thanks.

Refer to this page:

http://www.fixya.com/support/t1798043-cell_phone_turn

when wired to the battery it's getting full power.
so if the switch is set to anything but max it won't get full power. does it work on max?
does the fan stop and start over bumps? will it come on if you wiggle the wires? check those.
if there are no loose wires and the fan is not jammed in the heater box try a new motor.

I held down the "VCR" button in the top row and while holding it down I entered the code. Then I released all buttons and pushed power and LOW AND BEHOLD it worked.
RCA- RCR450c universal remote and a Orion VCR