Maytag Neptune MAH5500B Front Load Washer Logo
Anonymous
Anonymous Posted on Jan 07, 2008
Answered

MAH3000AWW My Washer completes its cycle and every once in a while it is till full of water. I just start the cycle over and it will work fine for days and then happen again randomly. I replaced the control board and wax motor a couple of years ago. This problem just started a few weeks ago. The belt seems to squeek more now. Any thoughts?

Answer This Question
  • Anonymous Jan 07, 2008

    By the way, This happens on larger loads.

  • Danow Jan 08, 2008

    I have the same problem. I checked the R13 resistor and it looks good. Haven't put a meter to it yet. I haven't replaced the wax motor yet but the door does lock and I assume if it didn't work the door wouldn't lock. This has happened before ... like your prb it doesn't drain sometimes. All I had to do was as you said by selecting spin but this time and the last 30 times last night it didn't work. I am going to replace the wax motor tomorrow and get a price on a board.

×

3 Answers

Anonymous

Level 1:

An expert who has achieved level 1.

  • Contributor 1 Answer
  • Posted on Jan 24, 2008
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Jan 24, 2008
Answers
1
Questions
0
Helped
492
Points
0

Went through the same routine, first repaired the upper control board R11/Q6 issue and replaced wax motor.
http://members.shaw.ca/gavb/index.html
Worked for a couple year and quit again so I bought a new board, close to $300 I think it made a huge difference I think they changed the programming to spin out better.

Danow

Level 1:

An expert who has achieved level 1.

  • Contributor 1 Answer
  • Posted on Jan 18, 2008
Danow
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Jan 08, 2008
Answers
1
Questions
0
Helped
492
Points
1

I replaced the wax motor and so far it is working fine. Wax motor must have been weak and didn't go out far enough to hit the switch.

  • Danow Jan 18, 2008

    Just replace the wax motor as I did .... cost me $10.00 .

    It came with instructions that were easy enough to follow. Just remember to unplug the washer first. Good luck!

×

Ad

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Governor:

An expert whose answer got voted for 20 times.
Scholar:

An expert who has written 20 answers of more than 400 characters.

  • Expert 196 Answers
  • Posted on Jan 14, 2008
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Governor:

An expert whose answer got voted for 20 times.
Scholar:

An expert who has written 20 answers of more than 400 characters.

Joined: Dec 29, 2007
Answers
196
Questions
1
Helped
113280
Points
300

Replace both the main control board and the wax motor. This sounds like a computer chip malfunction

As far as the squeak, make sure it is not the bearing located at the back of the tub under the large pulley.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

My maytag neptune mah3000aww spins slowly then reverses, then spins slowly. will not reach regular spinning speed. What is the problem?
it could be a balance problem. Most machines are programmed to abort fast spin if the drum is unbalanced. This can be caused by too much in there, or possible the contents have clumped together somehow. Try a spin cycle only with an empty machine and see if it reaches full spin
Read full answer
Feb 18, 2015 • Maytag Neptune Washer Door Mah3000aww
0helpful
1answer

Mah3000aww I have an older maytag neptune # mah3000aww. It is not working properly. It started not pumping all the water out. I would then change cycles to get it to drain & spin. Then the other d
replace timer. 30 to 50% of value of new machine
Read full answer
Jan 02, 2012 • Maytag Neptune Washer
0helpful
1answer

Won't progress beyond wash cycle -- start light is flashing. Cannot switch from "normal" to delicate or any other choice. Maytag Neptune TL FAV6800AW
So I understand the issue. Does the wash cycle start up? By that I mean if you release the washer top from the base do the tumblers turn once the water fill cycle is complete?

If you don't have the FAV6800A/FAV9800A Service Manual (you can't get it on line anymore) see this post Clutch Fix I describe how to release the washer top from the base to observe the wash basket. Don't raise during the water fill cycle wait till that completes.

Does the key pad beep as you press the other cycle select key pads?

This could be a Control Board issue...........Rich
Read full answer
Oct 16, 2010 • Maytag Neptune FAV6800AW Top Load Washer
1helpful
1answer

Washing not getting clean
ok, try this before you consider removing the bowl. 1st-- buy 2 pkts of bicarb of soda. 2nd---make sure machine has no clothes in it. 3rd-- empty the 2 pkts of bicarb of soda into the bowl. 4th-- select traditional wash mode , high water level, hot water fill. 5th-- push start. 6th-- let it fill and wash for about 5 to 10 min, then turn the machine off. DO NOT LET THE WASH CYCLE GET TO THE DRAIN OUT STAGE. ok now the machine is full water and bicarb of soda and turned off, LEAVE IT TILL THE NEXT MORNING.-- In the morning select traditional wash mode, high water level, hot fill , then push the start button. let it go thru the complete cycle and all the lint and dirt should be removed from the bowl. by the way once it has started to wash lift the lid and see if the agitator is working. good luck and please reply to tell me how you got on.
Read full answer
May 27, 2010 • Fisher and Paykel Fisher Paykel Intuitive...
0helpful
1answer

MAV4755A Top Load Washer: When I turn the dial to start wash cycle, nothing ...
if press button selection, make sure that no 2 buttons are pressed
Read full answer
Jan 27, 2018 • Maytag MAV4755A Top Load Washer
1helpful
1answer

I have a Maytag MAH3000AWW Washer. It will start
That is a common issue that is caused by the control board of the machine. You may need to request service to fix this issue. Usually it may be caused by a resistor. Replacing the resistor may make the machine to work for a while but the repair will not last longer. I believe that the machine control board next to be replaced. Something else may be causing the control board to go bad.

Perhaps you were able to feel a burning smell from the washer machine in previous days.

Standing water may be caused by the control board failure because the pump will not operate properly.
Read full answer
Aug 29, 2009 • Maytag Washing Machines
0helpful
1answer

MAH3000AWW Does not spin fast enough on spin cycle Clothes are still full of water when done.
hi there ..sounds like your appliance is not spinning at all........(a) check if your drain pump is working correctly..(simply fill water and turn to drain)..(b) possiblity that the clutch drive mechanism is badly worn and needs replaced

regards Sir Galahad
Read full answer
Aug 13, 2009 • Maytag Neptune MAH5500B Front Load Washer
0helpful
1answer

Maytag Neptune washer MAH3000AWW seems to backfill after cycle
It could be a leaking water valve. The MAH3000 has two flavors, the earlier model had (2) extra wax motors in the soap dispenser for the bleach and softener controls and the newer ones have the bleach and softener valves integrated into the water valve assembly.

Contact me via the www.neptunehelp.com site and let me know which serial number you have and I can detemrine which water valve you will need.

See www.neptunehelpsong.com for a funny new song dedicated to Maytag Neptune owners explaining the door latch wax motor issue.
Read full answer
Feb 10, 2009 • Maytag Neptune MAH5500B Front Load Washer
0helpful
2answers

Fisher Paykel will not drain
I had the same problem. After cut the power off for at least 60 seconds and then back on, as the manual suggests, the problem remained. Therefore I started putting the clothes out and bailing the water out. Once the water was down about half way the pump started working. I suspect the sensor was "stuck". I cycled the washer without clothes and it worked fine. Still working after several loads of laundry. The water level sensor will probably need replacing sometime soon.
Read full answer
Dec 04, 2008 • Fisher and Paykel GWL11 Top Load Washer
0helpful
1answer

Neptune MAH3000AWW will start to fill when start is pressed, but stops seconds later
either a faulty pressure switch / pot or faulty controller - either way you will need to call someone in.
Read full answer
Jul 24, 2007 • Maytag Neptune Washer
Not finding what you are looking for?

View Most Popular

Neptune MAH5500B Front Load Washer

  • Washing Machines

Related Question

My maytag neptune mah3000aww spins slowly then reverses, then spins slowly. will not reach regular spinning speed. What is the problem?

  • Maytag Neptune Washer Door Mah3000aww

Related Topics

502 views

Ask a Question

Usually answered in minutes!

Popular Questions

Maytag Neptune Error COde "nd"

Maytag Neptune MAH9700 Front Load...

My maytag neptune front load washer won't spin all the water out

Maytag Neptune MAH5500B Front Load...

Model FAV6800AWW will not pump water out if clothes are in machin

Maytag Neptune FAV6800AW Top Load...

Fabric Softener Won't Dispense

Maytag Neptune MAH6700A Front Load...

HOW TO FIX NF CODE IN MAYTAG WASHING MACHINE

Maytag Neptune MAH5500B Front Load...

Top Maytag Washing Machines Experts

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Brad Brown

Level 3 Expert

19187 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. Neptune MAH5500B Front Load Washer...

Neptune MAH5500B...

Loading...