How do i change a lemark ink cartridge - Lexmark X2350 All-In-One InkJet Printer

hi,
following images and steps may guide you.


first know the parts.

..

Tear open the black ink cartridge bag at the notch and remove the ink cartridge.
IMPORTANT: Insert the ink cartridge immediately to prevent any drying of the ink.





Remove and discard the orange cap.
IMPORTANT: Handle ink cartridge carefully to avoid ink transfer.




Insert the black ink cartridge into the printhead. User's




Press down on the ink cartridge until you hear it snap into position

Tear open the color ink cartridge bag at the notch and remove the ink cartridge.

Remove and discard the orange cap.

Insert the color ink cartridge into the printhead

Press down firmly on the cartridge until you hear it snap into position
Close the printer access door.




regards,
cseian

Hello ,

Start by opening your ink cover and read the LCD screen; this will alert you as to which ink cartridge is not being recognized; make sure the cartridge that it is telling you is empty has been changed.

If the unit is still not recognizing the cartridge you have changed, follow the steps below.

1. Unplug the power cord for the printer unit.
2. Open the ink cartridge cover and remove all ink cartridges.
3. Close the ink cartridge cover.
4. Plug the power cord back in.
5. Reinstall the ink cartridges.

Thank you,

Pat

No. Please use only Lexmark Ink.

More than likely, the HP cartridges will not fit properly and certainly, they would not pass the cartridge identification test when you turn the printer on.

Changing a printer cartridge is not complex but improper handling of the parts may damage the printer and the cartridge. If the user notices that while printing the ink comes out dry or faded, it may be time to change the ink or the toner. The user will know if it is time to change the toner because instead of a sharp image, one will get a faded image. It is time to change the ink cartridge when the printing comes out spotty or colors are used to replace others —for instance, blue for black or yellow for red. Remember, faded images signal the need to change the toner; spotty printing signals the need to change the ink cartridge get more help for change cartridge .
Hope this helps you.

Begin by making sure power is on and ink cartridges are installed. DO NOT connect the USB cable.

Insert your CD and install the software. Connect the USB cable when prompted by the software.

Note: If you get any "New Hardware Found" windows pop up, just close them out.

If you do not have a CD, use the Comment button to reply and I will lead you to the Lexmark site to download the software.

Thanks for using Fixya.

http://gdlp01.c-wss.com/gds/0300001548/MP620_GS_EN-US_V3.pdf

The Lemark Optrasc1275 printer is given me a error of 30 black toner but i have change the black toner.

just solved this on my lemark - open the top so cartridges in middle
put cleaning fluid on the 'pads to the right( i userefill kit cleaning fluid) on the 'far right pad' ( the ones that the cartriges sit on when lid closed - they're about under(ish) the on/off switch - i filled the little pads up until almost overflowed (aout 1ml) shut lid so cartridges go back onto the pads, leave for 10 mins, then print out 10 pages of something then repeat the clean again - mine took 3 times then works perfect - hope this helps

Does your unit have a printhead cleaning manager. Do this a few times. Check to see if you have to reset ink levels too.

Normi, The 1203 error as you suspected deals with the ink cartridge. This is a common problem and Lexmark has a troubleshooting procedure posted on their web site. Here is the link for the web page. http://support.lexmark.com/cgi-perl/knowledgebase.cgi?ccs=229:1:0:439:0:0&emeaframe=&docid=ENUS21870 Hope this solves your problem and please don?t forget to rate this posting.