All of a sudden my lcd tv will not power up there is power at the plug
Element FLX-1910
Problem: When the TV is turned on a picture appears for a few seconds and then the picture turns off. Audio is still heard.
Solution: Not a simple fix! This TV has 4 small florescent looking bulbs that act like a back light to light the image on the liquid crystal display (LCD). At least one of these bulbs is burned out or broken. The wires powering the broken bulb need to be cut and spiced together. Basically you’re bypassing the bulb and completing the circuit when cutting the wires going to the bulb on each end and splicing them together.
WARNING: This worked for me but no guarantee for anyone who tries it. This is a very involved procedure and involves completely dismantling your television. To be honest I don’t recommend anyone trying to fix it unless you are very technically minded and have a couple of hours to waste carefully tearing apart your TV. If anyone is willing to attempt this repair I am willing answer questions.
Cause of problem: It is my guess that this problem occurs when the TV is left on for extended periods of time. Like leaving the TV on when you fall asleep at night. My TV was left on a lot. I noticed that the plastic was melted and discolored where the bulb had burned out. (This can only be seen internally and is no way visible from the exterior)
As PAINTX said, one possibility is to check the wires/bulbs in the LCD Panel....mine can be easy found because the wire that connect one of the bulbs looks burned....after removed plastic,on LCD Panel corner, wire has no contact with the bulb....just need a solder iron and technical skills to repair it. After that, Picture looks normal.
If in your LCD TV, picture looks very, very dark, but you can see it seen, maybe you have to change Power Supply/Inverter Board (both circuit in same board, aprox. 50 dlls). Of course, also look for a defective capacitors, before buy the board.
If no picture at all, maybe the wires of the bulb lost contact.
Thanks PAINTX.
Good luck!
SOURCE: my element 19 inch flx-1910 tv will not power up
did you make sure the voltage, amperage, and polarity were matched tv to plug? The information is found on the back of your tv and the plug must match that. If they do not match, you might have fried your tv.
1,325 views
Usually answered in minutes!
same prpoblem
just started happening here
same
I canĀ“t find fix the problem, somebody could help me????
I had the same problem, sent it back for warranty work, they fixed it, and one month later (and outside of the warranty period), it is now doing the same thing again.
Mi LCD flx 1910 de 19" dejo de encender ,la fuente funciona bien pero no prende ni el stand by .Cual es la solucion?
Same problem. 19 Inch FLX-1910 will not power up.
I get sound, but I can't see any image!
Normal
0
false
false
false
MicrosoftInternetExplorer4
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
Element Electronics
FLX-1910
Problem: When the power button is pressed the screen turns
on momentarily and a buzzing sound is heard, then the screen goes blank and the
buzzing sound stops. Audio can be heard
fine but no image is displayed on the screen.
Just bought a 19" elements flat panel tv....the sound is hollow...?
×