Invicta Subaqua Noma Iii S Logo
Posted on Dec 26, 2009

The second hand on my invicta chronograph watch doesn't reset to zero

2 Answers

menatour

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 5 Answers
  • Posted on Sep 29, 2010
menatour
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Sep 29, 2010
Answers
5
Questions
0
Helped
11345
Points
12

Easier than you think.
Pull your Crown out to the FIRST stop (were you would normally set your date). Push the "A" button (top chrono button) for your dial at the "3 oclock" area, Push the "B" button(bottom chron button) for the second hand.

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 1 Answer
  • Posted on Aug 31, 2011
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Aug 30, 2011
Answers
1
Questions
0
Helped
9496
Points
2

On the Invicta Sub Aqua NOMA III 5511: open the protective crown gate, unscrew the crown (Counter clockwise) until it releases. Pull the crown out to the fully open position. Unscrew the base plugs preventing the chronograph buttons from being pushed. When both buttons may be depressed fully you can begin. Depress both chronograph button simultaneously for 2 seconds, you will see the second hand sweep the face. If it stops not resting at the 12:00 position depress your top chronograph button until the second hand is aligned with the 12:00 position. Now you can depress the bottom chronograph button once and it goes to the first subdial, press the bottom button again and it moves to the second subdial. Repeat until you are zeroed out.

Ad

1 Related Answer

Anonymous

  • 59 Answers
  • Posted on Aug 27, 2009

SOURCE: reset chronograph minute and hour hands to zero

pul crown all they way out
press top right button to set the minute hand
& bottom right button to set the hour
if not work then puch back crown to 1st click and do it same function ,, if still not working then pull crown again and push and hold both button for 5 sec. its reset ,, and try to adjust it again by pressing top & bottom button
hope that will help if not and you are in chicago
bring it to us
at
Amfix Jewelry & Watch Repair
203 N. LaSalle St
Chicago, IL 60601
312 641 7000

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

What are the buttons on a invicta watch..model 23696 used for?

This is a chronograph watch. The top button starts the second hand (the chronograph) the bottom button resets the chronograph to zero. You need to first press the top button to start and the press the top button again to stop. then press the bottom button to reset. The hands will not reset if you have not stopped by the top button.
0helpful
1answer

The seconds hand on my invicta subaqua reserve does not move. It only moves when I start the chronograph. I've read the instructions time after time and can not get it to work.

The hand that moves when the chronograph is working is not a second hand. It will rest at the 12 o'clock position unless you are using the stopwatch. If your Invicta has a second hand, it is one of those small dials on the watch face.
1helpful
1answer

How it works invicta clock mechanism ?

Your watch is battery powered or a 'quartz' watch. It is commonly refered to as a 'chronograph'. That is another word for stop watch.As well as telling time and the date, your watch can time how long an event lasts. For example, a horse race. You start the chronograph or stop watch when the horse starts and stop it when it crosses the finish line. When the next horse starts you need set it back to zero to time the next race.Operation is simple. The upper push button starts and stops the chronograph. Try it. Now with the chronograph stopped, push the bottom button. The hand return to the 12 o'clock position or the 'zero' position. Also notice the small dials on the dial or face of the watch. They record minutes and other increments of time. The large hand going around when you push the upper button is recording seconds. Hope this helps, Michael
0helpful
1answer

My big second hand on my chrono watch does not move

Yes that's common, most chronograph watch's a small subdial is the times second hand. The large second hand is only for the timing function of the chronograph.
11helpful
3answers

The seconds hand doesn't reset to zero when you activate the chronometer with the pusher A and stop it with the same one, you can reset with the pusher B, but it doesn't reset to zero y goes to...

CROWN SETTINGS:
1....... Running position/screwed
2 .......Date correction
3........Time correction

alpug_70.jpg

Procedure to set the mode using Push Buttons

Pusher A: Start/Stop Chronograph
Pusher B: Change to Chronograph mode/ Reset to zero

Note if by pressing button B and it doesn't reset to zero, you can adjust the time by following the procedure below

1. Set crown to position 3
2. Press pusher A to realign second hand
3. Press pusher B to realign counter hand at 6H
Note: For faster hand adjustment, hold pusher for 2 seconds or more

Hope this information will help you!
8helpful
1answer

I can't figure out how to adjust the offset chronograph

This is to adjust the seconds hand or minutes hand for the chronograph. Pull the crown out either one click or two ... depending on the models. Squeeze and hold the top and bottom buttons at the same time (timer stop and reset buttons). Hold down together for 2+ seconds. The chronograph hands should reset by spinning around and stopping at 0. If the don't stop right at zero, you can now adjust where they stop. Leave the crown where it is in that same position out. Press the top chronograph button and hold it down for fast movement or short presses for fine movement to adjust til it stops at the top. This will adjust where the seconds hand stops. Then click the bottom chrono button once. Repeat what you did with the top chrono button and it should allow you to fine tune the position for the next dial, and so on. When you are done, press the crown back in all the way to the normal position.
2helpful
1answer
1helpful
1answer

Invicta Gran Speedway CG second Hand reset

good after noon ! the hand of your watch is need to aline , so you need to go to the watc repairman,thank you! god bless !
2helpful
1answer

Invicta Ocean Ghost Chrono Model# 2636

Did you recently have a battery changed. A lot of times on chronos when the battery is changed the battery has to be short circuited to the AC. Which is done by taking tweezers. & touching the positive part of the battery to the part of the watch marked AC. Then try to pull the crown all the way out to time setting position press the top rt button & the second should move keep moving until it lines up with zero. If you haven't had the battery changed try what I told you to do with the crown & the top right button.
Not finding what you are looking for?

9,506 views

Ask a Question

Usually answered in minutes!

Top Invicta Watches Experts

Brad Brown

Level 3 Expert

19187 Answers

Ngoro

Level 3 Expert

3521 Answers

john h

Level 3 Expert

29490 Answers

Are you an Invicta Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...