I have a problem with the color faces are a pinkish color and i just put all new ink in also and i have error codes 3501 and 6203

Process Drive Fault"

Do you have another kit you can take from another printer.
Switch the printer off.
Swap out the kit with the one from the other printer.
Turn it back on. If it clears the fault when the printer is ready put back the new kit

Hi

You have stick residue in the print head. Just run the print nozzle for 2-3 times to get the correct color.

Also, be sure that all ink cartridges are full because if one of the color is empty, you cannot achieve the correct color when one ink color is missing.

Please let me know if you need more help

Dose The Dell Printer 160N Take 1 Or 2 Ink?

try cleaning the heads. Sometimes that will bring the colors back the way they should.

sounds like the linear adjustment is out of whack.....most projection type tvs, projection, lcd, plasma, have to be correctly aligned so that the color grids overlap each other to properly display the correct hue being created. you'd need the service code to re-adjust it, or have it serviced. also possible that one of the color grids is bad, but if you have all three (red,blue,green) colors showing on the entire screen area i would doubt it

Change Color Code By Going To Tools Then Error Console Choose Your Color And Then No More Pink(Are You A Girl

You are running low on your color ink cartridge. It cannot mix the primary colors right anymore and the color images start getting a pink-purple tinge to them. Get a new set of cartidges and install them and this should fix the problem fine. Hope this helps.

How do I resolve the error message "Calibration Page Not Found"? Error code: 3610 Question : How do I resolve the error message "Calibration Page Not Found"?
Answer : To resolve this error condition, correctly position a calibration page on the scanner. See the User's Guide for more information. How do I resolve the error message "Cover open"? error code : 3501 Question : How do I resolve the error message "Cover open"? Answer : To resolve this error condition, close the access door. The printer will not operate while the door is open. How do I resolve the error message "Color ink cartridge missing or not installed correctly"? Error Codes : 3511 Question :
How do I resolve the error message "Color ink cartridge missing or not installed correctly"?
Answer :
To resolve this error condition, reinstall the ink cartridge:

1. Remove the color ink cartridge:
   1. Open the printer access door by lifting from the front center of the unit.
   2. Wait until the printhead is idle and silent, then pinch the latch on the color ink cartridge with your thumb and forefinger and lift it out of the printhead.
2. Check the two electrical contacts on the ink cartridge for small marks, which should appear if the cartridge was installed correctly.
   
   If the electrical contacts do not have small marks:
   1. Reinstall the ink cartridge, making sure you press down on it until it clicks into position.
   2. Remove the color ink cartridge, then check the two electrical contacts on the ink cartridge again for small marks. Repeat if necessary.
   3. Reinstall the ink cartridge.
      
3. Close the printer access door.

NOTE: See the User's Guide for more information about removing and installing the ink cartridge.
If the error persists:

1. In the KODAK All-in-One Home Center, select the Help (?) icon.
2. Select Maintenance.
3. Select Firmware Upgrade, then follow the prompts to download the latest version of firmware, free of charge.

From Kodak support:
http://www.kodak.com/eknec/PageQuerier.jhtml?pq-path=9104/7269&pq-locale=en_US

Click on this link or copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Are the ink cartridges refilled or compatible? They may be defective.
Are they installed correctly (not in the wrong slots)?
** Note that even if they are replaced it will take SEVERAL pages before the quality returns

did you calibrate it?