Canon i9950, Operator error,5 amber blinks

panal board replace

Reset Procedures for Canon i550, i560, i850, i860, i865, i9100, i9950 Printers

1. Turn off Canon i550, i560, i850, i860, i865, i9100, i9950 Printers
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your Canon i550, i560, i850, i860, i865, i9100, i9950 Printers should respond as normal.

you done.

"Issue: ERROR LCD: Error Code 5010
Solution: Press ON/OFF switch to reset the multifunction device

Reset the device when it is not functioning properly.
If the device is not functioning properly or to clear memory, reset it.

1. On the operator panel, press and hold the button for one second. (The display will go blank.)

Note: It may be necessary to unplug the power cord if pressing the ON/OFF button does not shut off the printer.

2. Wait approximately ten seconds and then press the button again.

3. Wait until the device has completed its cycling process before submitting another job request."

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Try unplugging the power cord, letting it sit off for 30 seconds, then plugging it back in.

remove the printhead and clean the underneat replace it. the orange blinking will stop

1. Turn off Canon i550, i560, i850, i860, i865, i9100, i9950 Printers
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your Canon i550, i560, i850, i860, i865, i9100, i9950 Printers should respond as normal.

Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

The error code says that your printhead is bad and needs to be replaced. QY6-0049-000 around $40.00

Operator error.
Press printer's RESUME button.
If this doesn't clear the error, cancel printing and turn the printer off and then back on.
When press Resume button, ip3000 not responed(not print)

Reset the device when it is not functioning properly. If the device is not functioning properly or to clear memory, reset it.

1. On the operator panel, press and hold the <ON/OFF> button for one second. (The display will go blank.)
   
   
2. Wait approximately ten seconds and then press the <ON/OFF> button again.
   
   
3. Wait until the device has completed its cycling process before submitting another job request.
4. To clear error messages displayed on the LCD or if the printer is not functioning as expected, it may be necessary to simultaneously press Stop/Reset and ON/OFF buttons.
5. With the printer powered on, press and hold down the <Stop/Reset> button then press the ON/OFF button.
   
   
6. Once the printer is powered off, hold down <Stop/Reset> and then press <ON/OFF>.
7. clear any paper jam
8. May be your product requires repair service.
   

Many models of printers each with thier own little quirks. Check out the Manual -there is probably a comprehensive version on the software CD. Check out www.fixyourownprinter.com entering you make and model number. you could also reinstall the software. try these software first them come back