Auto channels i bought a jvc tv, model av32f577, with no remote or guide and i need to scan for channels but can cause i have no remote or guide. how do i manually do it by the front of the tv.

First make sure that the Source is set to TV and a good antenna/coaxial cable is connected to the TV. Use the Input button on the TV (to the left of the power button) or the Input Select button on the remote. Use the up/down arrow keys to navigate through the source list and press Enter to select that choice. (On the TV, the Input button is the Enter button.) Next press the Setup/TV Menu on the remote (or Menu on the right arrow button or Enter. Then go down to Auto Ch Memory and press the right arrow or Enter. With the up/down arrows, navigate to Signal Type and set that to Air (for OTA channels) or Cable with the left/right arrows. Now navigate to Automatic Search and press the right arrow or Enter. Wait for the scan to be completed.

I hope this helps. The steps are shown in the manual for the LT-19D610 on page 18. The manual is available from JVC on the product page: http://support.jvc.com/consumer/product.jsp?modelId=MODL028825 . The direct link to the manual is http://resources.jvc.com/Resources/00/01/47/J55D0221B.pdf .

Cindy Wells

Just do a channel auto search through the menu and channels should be memorized.

The TV user guide should provide the procedures of acquiring auto scan. For example, your TV may be acquiring functionality from satellites dishs or cable receiver devices. Performing an auto scan achievable with the remote control device with adjustment to settings on the channel buttons would produce a signal only with available transmitter stations. Performing a channel auto scan would display no signals without available receiver devices often acquired with susbscription from a provder either cable TV, sattelite or disk network, show on demand for example. However, performing an auto scan on a new Tv should simply display a count list of possible available channels on which signals could be display when any is provided. Good luck

taken from their support f&q section word per word

"try the following codes 10019, 0178, 10178, 0030, 10030, 0835, 10835, or for Dish Network try 627, 659 or 505. For Fios TV (Verizon), try the code 3264. These codes may not work on some universal remotes. If there is another code listed for Element Electronics in your universal remote control guide, please try that code. Refer to the Remote Control Guide under your TV’s model number for more information."

hi,you need to auto search first your your t.v set if nothing happen possible defect is the tuner.

If you want to get the original remote for this model (AV-30W776), you can find it at this JVC parts ditrubutor:

JVC AV-30W776 Replacement Part Remote Control

do u have the user manual for the TV? if you do the solution will be in there, if not (I suspect you don't) please give the make an model so I can try to look this up, but off the top of head there is no way to "assign channels" to a paticular remote setting.

I HAVE A YEAR 2003 GE TV
MODEL 27GT630
THE MANUFAFACTURERE WAS THOMPSON LTD
I LOST MY SET UP MANUAL
I HAVE A CABLE
MY GUIDE PLUS REMOTE REFUSES TO WORK AS WHEN I PRESS A KEY THE LIGHT ON THE REMOTE DOES NOT GO ON
I HAVE BEEN USING A REGULAR GE REMOTE AND IT WORKED GREAT
SOME HOW WHEN I TURNED IT OFF YESTERDAY I AM UNABLE TO GET BACK THE TV STATIIONS
I HAVE BEEN FOLLOWING THE SET UP GUIDE ON THE TV
LOCATION CANADA
AREA CODE T9K 2G9
CABLE YES
VCR NO

WHEN I PUT ON THE AUTO CHANNEL SEARCH IT GOES THROUGH THE SETTINGS AND THEN SAYS "NO CHANNELS SELECTED"

IT IS A BEAUTIFUL TV AND I DONT WANT TO DITCH IT
HELP ME

It's easy, you just have to go back into the menu setup for the auto channel/tuner setup and rescan for channels. I'd noticed this as well when playing around with the tv when I'd bought it and it had done the same to me.