HOW TO REMOVE FILTER ON FRONT OF MACHINE I HAVE LOST THE MANUEL AND I AM NOT SURE WHICH WAY TO TURN THE FILTER AFTER I HAVE REMOVED THE SMALL FRONT PANEL AND IF I GET IT OFF WILL THERE BE ANY WATER LEAKING OUT my machine is a washing machine hoover HNL7166

The drain filter on the Samsung model WF 328AAW/XAA is located behind the lower kick panel. To access it, you'll need to first unplug the washing machine and shut off the water supply. Then, you'll need to remove the lower kick panel by removing the screws that hold it in place. Once the panel is removed, you should be able to see the drain filter. It's a small, circular filter that is located near the base of the machine.
If the drain filter is clogged, it can cause the washing machine to not spin or drain properly. To clean the filter, you'll need to remove it and rinse it under running water until all of the debris is removed. Then, reinsert the filter and replace the kick panel.
If the drain filter is not the problem, there could be other issues causing the washing machine to not spin or drain. Some other possible causes include a faulty drive belt, a malfunctioning drain pump, or a problem with the control board. If you're unable to diagnose and fix the problem on your own, you may need to call a professional appliance repair technician for further assistance.

Filter at bottom of machine needs pulling out and cleaned on a regular basis. This is a common fault and the lights is telling you to clean the filter. It is a large filter that unclips at the bottom front of machine. Remove two small screws from the front of the filter located left and right and gently remove the front plate. Once removed you will see a metal filter clogged with clothing debris. Clean with cotton buds and a damp cloth till clean. replace all parts and you should have it working once again with a good heat source as well. Every 2-3 months is sufficient to keep it cleaned. Hope this helps.

http://www.cintelcorp.net/indesit-wd-10-manual you can get the manuel here.

This sounds like it is taking too long to drain. If the drain cycle exceeds eight minuites F 02 will flash. Shut the maching off and remove the access pannel below the door by removing the two screws at the front left and front right of the panel. After removing the screws pull down on the panel and remove. In the middle of the machine you will see the drain pump and motor assembly. Grasp the cap on the front of the pump and turn counter clock wise and remove cap and filter assembly. Make sure you have plenty of towels ready as plenty of water will come out when the cap is removed. Clean out the plastic filter tray and check to make sure nothing else is lodged inside filter cavity. Reassemble and it should work ok now.

Quite easy, Valve is removed by loosening two scews/or twisting valve off, remove the 2 hoses too...Remove wiring then refit..Turn off water 1st and electrics....Good luck, parts cost about £10

if your hotpoint has no obvious filter ( small flap on front ) its likely to be the type that has the filter built into the main exit hose from the drum to the pump. Clearing these is not as easy.

pull machine out and unplug it, on the rear there is a panel at the bottom which when removed you will see the pump where the exit hose attaches. From the pump to the drum is normally a wider black pipe and this contains the filter. removal of the pipe from the bottom of the drum is normally a jubilie clip but some have plastic clips that are easy to break. once you have dropped the pipe from the drum ( water goes everywhere ) you can then remove the white filter assembly which is like a shuttle **** with ping pong ball in it. clean out fully andd make sure its all back together as before.

Not easy but the blocked filter causes so many hotpoint issues. Its a pain the way they have built it inside the machine rather than making it user friendly.

Overfilling loads can cause small objects like pins, coins, and small socks to get between the tub abd Basket of your washer.

The basket is held onto the rear half of the outer tub simply by the bolt to the main pulley.
Remove the bolt, remove the pulley, and the basket shaft should slip right out of the bearings of
the rear tub.

Simply shining a light around between the basket and outer tub should confirm that there is something in there, since you have access to do this with
the front tub removed. Go ahead, remove the pulley and bolt, and if
the basket comes out, then check everything out.

If it doesn't, don't try pounding it out; stop there and go to plan B, which is a new basket
and tub assembly.

Front - loader: Remove Bellow
http://media.fotki.com/1_p,wbwdbgtqbsqkfbgxgtqsskgwtqkq,vi/kdtfgttdqxkfqrdrrdq/1/1303472/5961857/image45926img-or.jpg



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

If this is a whirlpool front load washer I have a model# GHW9100LW1 which has a filter at the front bottom of washer there is three screws to be removed then remove cover this should expose the water pump which has a cap on the front take hold of the grip and turn counter clock wise be sure to have a towel handy for there will probably be some water that will come out after loosening the handle all the way the filter part should pull out remove the trash and replace back in the pump note the filter will only go in one way re-tighten the nut and replace the cover that should fix the problem.

The leaks in a washing machine could be coming from many different places in the washer.

The first place you need to check is behind the washer, check the two fill hoses and the water mixing valve.

The next thing to do is to remove the front panel, set the washer on the regular cycle and turn it on to start filling.

Use a drop light and check all the hoses under the washer as the washer is filling. Make sure to keep your hands away from any moving parts.

If the hoses are ok, check the pump for leaks. When the bearings in the pump wear out, that is when the pump will get noisy and that could cause your Maytag top load washing machine water leaks.

Another place that the washer could leak water from, is the stem & seal on the holding tank. When washer leaks water from the stem & seal, the water leaks down the center of the transmission.

When the stem & seal need to be replace, the tub bearing has to be replace at the same time. This is an expensive repair if you have to pay someone to do it. If you do it yourself it will cost you about $110

you have got a blocked filter or pump the filter is located on the right hand side at the front of the machine down the bottom behind the plinth you can drain the water from there as well by pulling the small grey hose out pull the plug out of the end and place in a small bowl good luck when the water is out you can check the pump impeler as well clean the filter houseing and put it back all should b well unplug the machine b4 u start work