I have a logitech remote for my tv, just bought a wii game. Do i need to program it into my remote as i cannot get the wii to work?

Go into the Wii channel and go to settings then look for calibrated remote. Make sure the new wiimote is on. Set the Wii controller on a flat surface and press callibrate. The wiimote will be ready to use .have fun.
Hope this helps.

from where did you bought it

Hello there

Hold the Wii Remote upside-down with the buttons facing downward.

Tap the remote firmly against the palm of your hand three times to remove any dust sitting between the buttons and the electronic circuit board inside the remote.

Turn the remote upright and press one of the buttons. If the problem continues, Open your Wii Remote's battery door

Check that your Wii Remote contains two new "AA" batteries or a charged battery pack. Check that no corrosion is present on the battery's metal elements/connectors.

Use a cotton swab to clean the remote's battery element/connectors if corrosion is present.

Check that the Sensor Bar cable is inserted firmly into the back of your Wii gaming system. The Sensor Bar needs to be centered above or below your television so the Wii Remote can transmit signals to the gaming system.

Stand three feet away from the Wii gaming system/Sensor Bar.

Aim the remote and press any button to test the device.

If the remote is not working, stand five to 10 feet away from the gaming system and try the device. The Wii Remote works best three to 10 feet away from the gaming system/Sensor Bar.

Move any objects blocking the signal from the remote to the gaming system/Sensor bar--candles, other remote controls (TV/cable box) and wireless computer devices/cellular phones.

Also, if any sunlight is coming in through a window, close the curtains or blinds to keep the light from interfering with the remote's signal.

Turn off and unplug your Wii gaming system. Leave the unit unplugged for one minute. Plug the gaming system back in.

If the remote still aint working;

Turn the Wii system on. Press and hold the red "SYNC" button for 15 seconds when the "Health and Safety" screen appears on your television. The "SYNC" button is behind the small door on the front of your Wii unit.

Release the "SYNC" button. Remove the battery cover and batteries/battery pack from the back of your Wii Remote.


Press and release the red button located under the battery compartment. The blue lights on the front of the remote will blink

Press and release the "SYNC" button on the front of your Wii gaming system. The "Player" light on the gaming system stops blinking and stays on, the resetting process is complete

Hi,

I just thought you should know the Harmony Remote is only able to control any device that uses infrared control. Unfortunately the Wii console uses Bluetooth technology which means the Harmony Remote would not be able to control it.

Hope this helps you!

-Kennedy

Have you checked the remote sensor strip that you mount on the TV is there? Is it connected to the WII console?

The Logitech Harmony 520 remote control is programmed through the Harmony Setup Software you can download from here.

Once installed, you will simply run the software, and select the devices you would like to control from menus. The software finds the right codes for you and loads them into your remote control.

I hope that helps.
_____________________________________________
Harmony 520 Manual Download
Logitech Harmony Firmware Update
Harmony Win Software Download
Logitech Harmony Safe Mode Fix
Harmony Remote Glow Light Fix

I can help you with your Logitech Harmony 550 remote control.

The Logitech Harmony 550 remote control is programmed through the
Harmony Windows Setup Software.

Once installed, you will simply run the program and select the devices you would like to control from menus. The software finds the right codes for you and loads them into your remote control.

I hope that helps.
_____________________________________________
Harmony 550 Manual Download
Logitech Harmony Firmware Update
Harmony Win Software Download
Harmony MAC Software Download
Logitech Harmony Safe Mode Fix
Harmony Remote Glow Light Fix

press the red button at the back of the remote and then open the cover at the front of the wii and press the red button

Depending on the type of inputs you have on your TV, you may need to order a component cable. The one that ships with the Wii is just a composite cable and some high-end TVs might not have the right connection for it. Fortunately, you can get this cable for less than $5 at monoprice.com. Good luck!

http://www.monoprice.com/products/product.asp?c_id=108&cp_id=10830&cs_id=1083001&p_id=3566&seq=1&format=2

Ok well first of all, you'r first remote is working fine right? Ok lets move on to the second remote. On the left of the wii there is a little hatch that you can open, in there there is the slot to insert a SD memory and there is a red button. Press the red button and wile that is hapenning grab the wiimote and pres 1 and 2 at the same time once. The lights on the remote should start flashing and it will be in sync all together.. And voila two wii remotes working fine,

-Alex