Question about Kenmore 22422 Top Load Washer

1 Answer

Kenmore heavy duty series 80 model 110.25842400 will not spin.

Will not spin

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,122 Answers

If it will not drain or spin it is a bad lid switch,if it drains but will not spin it is the motor coupler,tip it back and look between the motor and trans that is where the coupler is located-mike

Posted on Feb 19, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

70 Series Kenmore Washer Agitates in Heavy Duty regardless of switch selection


Yours is a 2 speed motor. Does it spin in 2 different speeds. If so, then it most likely is designed with only to agitate in 1 speed. If it only spins in one speed, then your motor is defective

Nov 03, 2017 | Kenmore 24032\24036 Top Load Washer

1 Answer

Is there a belt on a kenmore ultra fabric care heavy duty 80 series


No. What is the problem you are having? Let me guess, it's not spinning or agitating?!
What is the model number listed under the lid?

Nov 03, 2012 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore washers, heavy duty 80 series, no spin


Hello, Your problem is going to be with your lid switch, this is located normally either in the control panel or about half way down on the right side under the lid. This is a safety feature to stop you opening the lid while the machine is in a high spin. Once you have located the switch trace the wires back to the wire harness in the control panel. Disconnect the lid switch from the wire harness and with an ohms meter check for condinuity on pin 1 & 3 (the 2 outside pins not the middle this is a ground) You should find you have no condinuity and should replace this switch. If you have any other questions or concerns please feel free to comment again. Good Luck!! Mike

Oct 14, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Direct drive-type Kenmore washer will not spin.


Check the video at the following link. I think you will find it helpful. Hope so and best wishes.

http://www.youtube.com/watch?v=WLPGs2UMUJc

Sep 14, 2009 | Washing Machines

1 Answer

No spin cycle


Something simple. Plug off the wall mains. Find your pump, dismantle to locate block. Before that you could check out your filter to clean out.

Mar 12, 2009 | Kenmore Washing Machines

2 Answers

Kenmore 80 series runs but dont blow hot air


Where is the location of the heating element for a Kenmore 80 series dryer heavy duty model # 77834795

Dec 09, 2008 | Kenmore 63942 Dryer

1 Answer

Won't spin or drain


Check to make sure your lid switch is working.

Nov 17, 2008 | Kenmore 22422 Top Load Washer

Not finding what you are looking for?
Kenmore 22422 Top Load Washer Logo

382 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5692 Answers

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...