Question about Maytag Neptune MAH6500A Front Load Washer

1 Answer

Maytag neptune front load washing machine will not fully discharge water after the rinse cycle...HELP???

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,554 Answers

Check the drain hose and clear it from any debris that might be blocking the water from draining out completely. If the drain hose is clear of debris, check and clean the pump. Disconnect the machine from the power outlet before servicing for safety purposes.

Remove the rear access panel to access the pump and disconnect the wiring harness from the terminals of the drain pump and the pressure switch.

Loosen the clamps holding the drain hose and the tub hose to the pump assembly. It is a good idea to spread a towel under the pump before loosening the clamps.

Remove the hoses and rotate the pump assembly counterclockwise to release the pump assembly support legs from the keyed slot in the base of the washer. Remove the pump assembly from the washer.

Clear the pump impeller from any debris that might be causing it to work improperly. Clean the tub and the drain hose.

Reassemble the pump, the hoses, and reconnect the wires to the terminals of the pressure switch and the drain pump. Reinstall the rear access panel and run the machine.

Replace the pump (part #25001052) if water still do not drain out completely.

Remove the plastic bag covering the pressure switch. Press in the locking tabs on the back of the pressure switch and pivot the pressure switch off the pump bracket.

Grasp the pressure switch and lift the nipple of the pressure switch from the pump cap.

Install the pressure switch into the new pump assembly in reverse of the steps above.











Posted on Feb 24, 2010

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Put detergent


MLG2000A - Maytag Neptune Super Stack SL-3
1 - Select Wash/Rinse Water Temperature
2 - Select Options (Max Extract, Extra Rinse, Signa)
3 - Select Cycle
4 - Load the Clothes Washer (add detergent on top of the load in the tub, and additives [fabric softener, bleach] in their dispensers).
5 - Start the washer.
This is according to the owner's manual I have. Has worked for 14 years for me.

Jan 14, 2014 | Maytag Neptune MLG2000A Front Load Stacked...

1 Answer

My Maytag Neptune front loader always retains water after the rinsing cycle is complete. This has lead to mold in the door gasket and a moldy smell. Is it normal for water to stay in the machine after the...


pump is probably clogged not allowing all water to drain out. Should never see water in the tub at the end of a cycle. About once a month you should run your washer through a cycle with hot water and bleach. Doing that should keep the moldy smell down.

Mar 15, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Water drips out of front door


There does obviously need to be water in the drum to wash or rinse the clothes, however it may be the water level is now higher than normal , check for any blockages and check any drain pump filter.If all o.k. it may be the door seal is leaking .If under g/tee call maytag for repair

Jan 29, 2009 | Maytag Neptune MAH5500B Front Load Washer

3 Answers

Maytag washer shutting off on rinse cycle


Hi there,

If the washer is not completing the Rinse cycle there may be problem with:

Lid switch
Motor coupler
Belts
Clutch
Drive motor
Drive pulleys
Transmission
Agitator

Let me know if you need further assistance.


Regards
Ellin

Sep 26, 2008 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag Neptune rinse cycle doesn't start.


cold water valve screen plugged or bad valve, just check it!

Aug 06, 2008 | Maytag Neptune MAH6500A Front Load Washer

1 Answer

Maytag Neptune MAH4000


Are you getting cold water to fill ?How is the water pressure?Timer maybe at fault here.

Jun 09, 2008 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag Neptune Top Load Washer - Rinse Cycle won't run - Machine says nF


Sounds like the 'Wash water' is not pumping out fully,You need to drain the water by lowering the empty hose into a bowl & check the pump for a blockage ( if the pump is an 'electric one' check that it is working). TURN POWER OFF FIRST

Oct 25, 2007 | Washing Machines

2 Answers

My Maytag front loading washer does not fully rinse cloths MAH8700A. I purchased this washer about 6 months ago. I usually wash small loads but have noticed it doesnt matter what size load. When first...


Is the drain path free-flowing? That is, does the water eject freely during spin/rinse? Maybe there's a restriction in the line, or it's too high above the washer.

Feb 25, 2007 | Maytag MAH8700A Front Load Washer

Not finding what you are looking for?
Maytag Neptune MAH6500A Front Load Washer Logo

332 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

606 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...