Hello, i would like to know how can i reset the factory settings in service menu for the LN32a330? The people in samsung move some color settings there, and now it look HORRIBLE, but i dont know what the parameters where or how can i put then back as they came from the factory in the service menu.. THX
Re: Hello, i would like to know how can i reset the...
You may not need to reset from the service menu. Try holding down the EXIT button on the remote until you get a prompt asking for the OK to reset to the default settings.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
In my openion, Its problem of hardware in your TV and signal processing circuits are involved. It might be problem of Firmware (programe to control the performence over all) Philips can advise you better in this regard.
Do a hard reset to this set, and check thereafter. There are two types of reset to TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight; will be better. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.
It sounds that somebody have entered into its service menu options, and changed the data values to audio settings there. You must get into its service menu again and must adjust these data values to its original factory settings. you needn't open the set, but the work is somewhat skilled one. If you wish to get more details about how to its service mode, and make it to factory reset, check this link. Details are there. Be sure that you can do the adjustments, before adjusting any data values there. Do not tamper with it. If you're not sure, seek help of any experienced service technician.
This is the reason I am careful about walking people into the tech menu on sets--one wrong move and poof!
If you by a miracle find the full service manual it would have the information needed (if set has this) for a hard reset---other wise you would have to try to with the manual reset every setting to factory one at a time...........
Hello there Sir, If you are using a standalone Screen use the "Menu" button on the screen, go trough the menus to find "reset to Factory settings" or "Recall factory settings" then it should be working fine. If there is color all over the screen (all blue or yellow) thre might be a bad connection with the cable moving it a litle might fix this.
Hope this helps
Thank you for using fixya Leo Ponder PLEASE VOTE FOR ME IF THIS WAS HELPFUL
Hello, try resetting back to factory default. If it asks for a code its usually 0000. You can acess this through menu. After that try auto tuning and that should work. If all else fails switch it off at the point and leave it off for a minute and switch it on and see if that resets it.
Hello
To get into the fatory setup, there is a metod for Samsung TVs. You just follo these steps, and will reach there. OK
[1] Turn the Power Off.
[2] On the remote control press "MENU" followed by 1,8,2 and "Power" in sequence.
[3] You should no see the service menu. To exit the service menu always select "RESET".
The service menu will guide you to the factory defaults. Note that upon entering the service menu, all user menu settings will revert to Factory Defaults.
If you do not have its remote control, the you will probably have to contact Samsung Electronics division in your country.
Has anyone been playing with this TV, i.e. repairing it, replacing boards etc?
I believe - do not know it for a fact - that Samsung has this protection in palce which identifies the boards in a TV and once you switch a board the TV needs to go through a service re-administration to remember its current configuration.
There's no explanation of why would a TV need to do that other than to restrict users to Samsung service centers only.
Again I do not know this for a fact, but I have seen other Samsung TVs that do exactly the same and they start doing it upon replacing boards on them. It's a simple logic.
go into analogue tv press menu move down to settings you should be able to enter plug and play in menu press ok( if you can not enter it you are not in analogue )
if not solve problem try this !! warning !!
you will enter the service menu DONT ENTER OR CHANGE ANY OTHER ITEMS THAT ARE DISPLAYED AS TV WILL NOT WORK IF YOU DO
With tv in standby press INFO / MENU / MUTE / STANDBY on remote
then use ONLY DOWN nav-key move to number 12 FACTORY RESET
press RIGHT nav-key will reset all tv settings to factory ones
PRESS STANDBY TO EXIT on remote
you will have to RETUNE after tv after
×