A Chrysler Transponder Key once programmed into a one car cannot be programmed to work any other car. The transponder code identification is learned by the Sentry Key Immobilizer Module during programming. The Sentry Key Immobilizer Module sends the "Secret Code" to the transponder key and is retained by the transponder key during programming. After programming of the transponder key identification to the Sentry Key Immobilizer Module and the Secret Code is exchanged, the Sentry Key Immobilizer Module will ask for the transponder identification and the Secret Code every time the key is turned to ON or START.
No Emergency "Start" procedures for Chrysler vehicles.
Chrysler Key Operation and Programming Model: 300 Year: 2005 - 2008
Model: 300C Year: 2005 - 2007
Remote alarm / central locking System Operation
- Pressing key LOCK button activates alarm and central locking.
- Pressing key UNLOCK button once deactivates alarm system and unlocks driver's door.
- Pressing key UNLOCK button twice within 5 seconds deactivates alarm system and unlocks all doors and trunk.
- Pressing trunk lid button twice opens trunk lid.
- System will automatically lock all doors when vehicle is driven above 15 mph.
- Additional functions can be set to respond to the transmitter.
Programming When
- Key transmitter added or replaced.
How
- Key transmitter is programmed during immobilizer programming procedure.
Immobilizer System Operation
- Switch ignition ON.
- Immobilizer warning lamp illuminates for approximately 3 seconds.
Programming When
How:
NOTE: Two programmed key transmitters must be available for the following procedure to operate. If none available key transmitters can only be programmed using diagnostic equipment.
- Insert first programmed key into ignition switch.
- Switch ignition ON for at least 3 seconds but no longer than 15 seconds.
- Turn ignition OFF and remove key.
- Withing 15 seconds insert second programmed key into ignition switch and turn ignition ON.
- After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will flash.
- Turn ignition OFF and remove second programmed key.
- Within 60 seconds insert non programmed key into ignition switch and turn ignition ON.
- After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will illuminate for 3 seconds.
- Switch ignition OFF.
- Remove Key.
Check operation of programmed key transmitter.
Repeat procedure for additional key transmitters if required.
Model: 300M Year: 1999 - 2003
Model: Concorde Year: 1998 - 2003
Model: LHS Year: 1998 - 2001
Model: PT Cruiser Year: 2000 - 2005
Remote alarm / central locking System Operation
- System will automatically lock all doors when vehicle is driven above 15 mph.
- Pressing remote transmitter UNLOCK button once deactivates alarm system and unlocks driver's door only.
- Pressing remote transmitter UNLOCK button twice within 5 seconds deactivates alarm system and unlocks all doors.
- Alarm / Central locking functions can be altered using remote transmitter.
Programming When
- Remote transmitter added or replaced.
How:
NOTE: One programmed Remote transmitters must be available for the following procedure to operate.
- Obtain all remote transmitters.
NOTE: Any existing remote transmitters not used during programming will become inoperative.
Using a programmed remote transmitter proceed as follows.
- Press and hold remote transmitter UNLOCK button.
- After holding the UNLOCK button for at least 4 seconds but no longer than 10 seconds, press remote transmitterPANIC button for at least 1 second and release both buttons.
- Ensure acoustic signal is emitted indicating programming mode active.
- Within 30 seconds carry out the following procedure for each remote transmitter (including previously programmed remote remote transmitter)
- Press any button of each remote transmitter to be programmed.
- Ensure acoustic signal is emitted after each remote transmitter operation.
- Programming must be completed within 30 seconds.
- Switch ignition OFF or wait 32 seconds to exit programming mode.
Ensure final acoustic signal is emitted.
Replacement remote transmitters can also be programmed using diagnostic equipment.
Immobilizer System Operation
- System arms after switching ignition OFF.
- Switch ignition ON.
- Immobilizer warning lamp illuminates for approximately 3 seconds.
Programming When
How
NOTE:Two programmed key transmitters must be available for the following procedure to operate.
- Obtain all keys.
- Using first programmed key turn ignition switch ON and wait 3 seconds, return to OFF position and remove key.
NOTE: First and second programmed key operations MUST be performed within 15 seconds.
- Insert second programmed key and switch ignition ON.
- Wait approximately 10 seconds.
- Ensure immobilizer warning lamp begins to flash and an acoustic signal is emitted.
- Switch ignition OFF and remove key.
- Within 50 seconds, insert new key and switch ignition ON.
- Wait approximately 10 seconds.
- Ensure acoustic signal is emitted and immobilizer warning lamp remains illuminated for 3 secondsindicating programming completed.
For each additional key repeat procedure starting from the beginning.
Replacement keys can also be programmed using diagnostic equipment.
Automotive and Commercial Locksmith Chrysler Remote Control Programming...
×