DOES RESET BUTTON PRESS AND RELEASE TO RESET5?

Sounds like you need to reset your Oil life/ maintenance reminder light. (also, double check your oil level)

To reset Oil life on a standard dash stlye:
1. pres and release the TRIP/RESET button until the message center displays SETUP MENU HOLD RESET
2. Press and hold the TRIP/RESET button for 2 seconds until the message center displays RESET FOR SYS CHECK
3. press and hold the TRIP/RESET button for 2 seconds until the message center displays OIL LIFE xx% RESET IF NEW
4. Press and release the TRIP/RESET button until the message center displays HOLD RESET IF NEW OIL
5. Press and hold TRIP/RESET button for 2 seconds and release to reset oil life to 100%
6. Message center will briefly display OIL CHANGE SET TO 100%


With a message center cluster the procedure is as follows:
1. press and release SETUP button until message center displays PRESS RESET TO BEGIN SYSTEM CHECK
2. Press and release RESET button until the message center displays HOLD RESET IF NEW OIL
3. Press and hold RESET button for 2 seconds and release to reset the oil life to 100%
4. The message center displays SETUP MENU HOLD RESET


Hope this is what you need/ are looking for. Goodluck & let me know how it goes, or if you have a different problem.

Cause: Head too hot, exceeds the threshold, usually the color Catridge
Solution:

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

To solve your problem follow the instruction step by step...

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.
Connect cable power, turn on printer again, now this printer ready to use

To solve your printer problem using the following directions..

Follow this instruction step by step.

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Follow this instruction step by step.

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Follow the instructions step by step

1. Turn off printer, cable power still plug in,
2. Press Stop/Reset button don't release
3. Press Power Button don't release and than release Stop/Reset button
4. Press Stop/Reset button 2X , wait until service mode to " 0 "
5. Turn off printer, cable power still plug in
6. Press Stop/Reset button don't release
7. Press Power Button don't release and than release Stop/Reset button
8. Press Stop/Reset button 4X , wait until service mode to " 1 "
9. Turn off printer, and loose cable power, wait one minute.
10. Connect cable power, turn on printer again, now this printer ready to use.

1. Switch ignition OFF.
2. Press and hold button "A" - fig. 1 or fig. 2.
3. Turn ignition key to position "I".
4. After 5 seconds the words "OIL SERVICE" or "INSPECTION" are shown together with the message "reset" or "re".
5. Release button "A". Press and hold button "A". After a futher 5 seconds the message "reset" starts to flash.
6. Release button "A". Press and release button "A" again.
7. The new service interval is now displayed.
8. Press and release button "A". The message "END SIA" is now displayed.
8. Switch ignition OFF.

Fig.1


Fig.2

Just bought a STARTER Sport Watch Model# STW14 @Walmart

TO CHANGE TIME: 1. Press and release MODE button quickly 3X in a row(top middle no.(Seconds will flash)& change Seconds by pressing START button 2. Press & release RESET button 1X quickly(Minutes will flash) & you change Minutes by pressing START button 3.Press & release RESET button 1X quickly(Hour will flash) & you change Hour by pressing START button. 4.Press & release RESET button 1X quickly(Date will flash) & you change Date by pressing START button.5.Press & release RESET button 1X quickly(Month will flash) & you change Month by pressing START button 6. Press & release RESET button 1X quickly(Day of week will flash) & you change Day by pressing START button 7. Press & release MODE button 1X quickly to return to Normal use
TO SET ALARM: 1. Press and release MODE button quickly 2X in a row(Hour will flash)& you change Hour by pressing START button 2.Press and release RESET button quickly 1X (Minutes will flash)& you change Minute by pressing START button 3. Press & release MODE button 1X quickly to return to Normal use
TO VIEW MONTH & DAY: 1. Press & Hold START button 2.Just Release START button to return to normal use.
TO USE STOP WATCH: 1. Press and Release MODE button quickly 1X 2. To START stop watch: Press START 1X quickly 3. To STOP Stop watch: Press Reset button 1X quickly 4. To RESET Stop watch: Press & Hold START button and press RESET button quickly @ the same time, 2X in a row 5.Press & Release MODE button 1X quickly to return to Normal use

Resetting Oil Service Light on your 2002 - 2006 MINI Cooper and Cooper S, and 2007 - 2008 MINI Convertibles:

1) Press and hold the trip button
2) Insert key and turn to position 1
3) Watch for RESET to appear
4) Release the button, then press & hold it again
5) Wait for the RESET to flash
6) Release the button, and then press & release (once only)
7) Service interval should then be reset to next interval
If that didn't work, try this:
1. Push the Trip Button
2. Turn ignition key to position 1 and 51A will appear to left of mileage
3. Release trip button
4. Wait 3 seconds
5. Push trip button
6. Wait (5-8 seconds) for RST to appear in left corner
7. Release trip button
8. Push trip button
9. 15000 will appear as new service interval
10. Release trip button

Or this:
1. Press and hold the trip odometer button.
2. Insert car key and turn it to the fi rst position (not the second position).
3. You will see 51A come up in the trip odometer area.
4. Release, then press and hold again.
5. Watch for the word “RST” to appear on the Odometer indicator.
6. Release, then press and hold again.
7. Wait for the “RST” message to fl ash.
8. Release, and then press & release (once only).