Panasonic PT-50LC13 50" Rear Projection HDTV Logo
Posted on May 14, 2010
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

TV does not turn on, blinking green on off button.

The replace bulb message has been coming on for some weeks now, but once you turn set on and off the TV comes on and everything looks fine. However, today the on off button only flashes green or red, TV won't come on. Is this related to bulb or a separate problem? How difficult to change bulb if that is the problem?

2 Answers

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Jun 13, 2010
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: Jun 13, 2010
Answers
1
Questions
0
Helped
381
Points
1

I replaced the ballast kit and I have 5 blinking yellows lights and it doesn't turn on!!!

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.

  • Master 3,130 Answers
  • Posted on May 14, 2010
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.

Joined: Mar 22, 2006
Answers
3130
Questions
5
Helped
1650343
Points
8439

That should be in the owners manual
techman
most sets havev a small door thathas has a screw on it and the bulb is inside a small cage you pull out
techman

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Blinking Green Light on Mitsubishi DLP 52525

the circut that detects the bulb has been also failing in these sets
and the conversion chip that controls the picture , and the transformers are not putting out the full power they are supposed to.
this set will need to be tested to determine the exact cause or causes
1helpful
1answer

Magnavox tv when the power button is pressed the green light comes on but nothing else happens; there's no picture or sound or nothing; but the green light simply stays lit (no blinking).

Hello,

first, press the channel -/+ button on the TV. If that doesn't turn on the TV, then it means you have to replace the bulb of your TV. The bulb is most likely dead.

Replace the bulb and your TV should be restored.

Let me know if you need further assistance.

Regards.
0helpful
3answers

I have a Mitsubishi WD 52628. I replaced the tv

try turning it on hold the menu button for eight seconds menu pops up try reseting the settings again as before you had the problem
0helpful
1answer

Panason PT-50LC13 TV won't come on, light blinks green then red

Ballast failure is more that likley the problem. Is the lamp light blinking,...once every 5 seconds? Discontinued part and can only be purchased used or rebuilt. Rebuilt units are available, check Ebay. Have a service type person confirm problem before throwing good money after bad!
0helpful
1answer

I just replaced the DLP Lamp and housing on a 50' Samsung DLP tv.

CK your Fans make sure they are running or set will not come on.also if you can solder resolder power supply board.
7helpful
3answers

Tv plays for a few minutes then shuts down. the red light blinks.

You need reset the lamp timer after
replace the new lamp.In the remote control pres menu------setup------lamp timer----message do you replace a lamp appear----press yes----and ok.
0helpful
1answer

Blinking green light and clicking noise AFTER bulb replacement

do this. press and hold device and menu button on set for 5 seconds. this will retrieve a 2 digit error code .. the led will flash the first digit and pause the flash second digit. This unit is known to have capacitor problems on the power board. getting to these capacitors involves taking alot apart. let me know error codes and we can continue troubleshooting
1helpful
2answers

Panasonic model# PT-50LC13

It very well could be the ballast. I unfortunately have this tv and keep extra bulbs because they go out about once a year. Last time when I replaced the bulb the tv blinked and the red lamp light flashed like it does when the bulb is bad. Ballast repair kit fixed it up. This is certainly a design issue but you'll get no help from Panasonic. If tv comes on the goes out after a while, clean the fan filter.
0helpful
2answers

Sony LCD projection TV - bulb problem

Hi! sweet123,

Please answer this question. Were the 4 bulbs visabley bad; say broken or did they have a milkey look, or broken wire inside? In other words did the bulbs you replaced look as good as a new unused bulb? Please reply.

toprol
Not finding what you are looking for?

391 views

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

5755 Answers

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...