My call answer button don't work is there an any button answer mode.

You may have seen this answer before on the sony support page and tried it with no luck, but the following DOES work. The trick is that you have to do it for a LONG TIME (I didn't time it, but it was maybe twenty seconds or so):

Hold down the EJECT and POWER buttons on the dvd player simultaneously, until you see a message that says DEMO MODE OFF (or something similar to that - I forgot to write the exact message down). When you see that message, let go of the buttons, and the tray will eject/open. Again, the trick is that you have to hold both buttons down until you see the message appear on the screen.

Hope this helps.

Not an answer per-se but an endorsement of Don Maggard's answer for the 2015 rdx with a genie. This is the only process that has worked for me. The process in the car's manual was flawed. Thank you, Don.

Press button [6] to enter tuning mode.Press either [2] or [4] to tune upwards or downwards.or Press button [3] and then enter a two digit RF frequency no (if you know the RF no from your transmitter). ie 36 for a vcr.You might have to press either button [1] or [5] to 'store' the channel, before finally pressing button [6] to come out of tuning mode

Without knowing the model of your phone I can't give you a definite answer, but on many Uniden DECT 6.0 phones you press and hold the # button to switch out of silent mode.

You can get the model by selecting the model of your phone from the list beginning at
http://www.uniden.com/owners-manuals/dect-phones/scat/dectphones_mnl/

I think that's Demo mode.
I got stuck there too.

This is what worked for me:

1. Power the radio off (hold the power button in top left corner in for several seconds)
2. Remove face plate
3. Hold in reset 10 seconds
4. Press push-menu dial/button 3 or 4 times
5. Insert cd and hit source to switch to tuner before cd starts

Not all of these steps may be necessary.
I suspect having the power off before the reset button was the important part.

Follow the instructions step by step

1. Turn off printer, cable power still plug in,
2. Press Stop/Reset button don't release
3. Press Power Button don't release and than release Stop/Reset button
4. Press Stop/Reset button 2X , wait until service mode to " 0 "
5. Turn off printer, cable power still plug in
6. Press Stop/Reset button don't release
7. Press Power Button don't release and than release Stop/Reset button
8. Press Stop/Reset button 4X , wait until service mode to " 1 "
9. Turn off printer, and loose cable power, wait one minute.
10. Connect cable power, turn on printer again, now this printer ready to use.

I know it's been a year since this question was asked, but I was trying to find the answer today and finally figured it out. I thought I would answer for someone else.

I have a sportek SP1020ZEL. Pressing mode first and then alarm did not work for me. Pressing mode first on my watch only put it into the stopwatch mode, and then pressing the alarm button is for reseting the stopwatch. So I tried it the other way around, and it worked.

First, press and HOLD the alarm button (bottom right button) and then the mode button (bottom left button). My sportek doesn't show a little bell symbol, but I noticed that with one press all the days of the week showed and when I pressed again all the days disappeared. So I waited for the hour and found that when there is no days of the week visible the hourly chime is off. I don't think this works with all sportek watches but it is worth a try. (I did not try holding all the buttons for 5 seconds).

On the base set, with the phone in standby mode, press the [ANSWER ON/OFF] button. If it's not in the state you want, press it again to change.

In your game Options Reasign the buttons in the Controls. Remember to say Apply or Accept. otherwise it wil still be tha default settings that you would be using. Hope it will work. zohanson

I had the same problem. The many instructions available don't have quite the right details. This worked for me:

1. Turn off the BT150 by holding down the answer button about 5 sec. until the blue light goes off and is not flashing.
2. Turn on the BT150 by holding down the answer button about 5 sec. until the blue light flashes.
3. Keep holding the answer button, and press and hold the volume + button for another 5 sec. until the blue light comes on solid.