Hello -Just looking for help on fixing a service code 66 which comes up when you turn the power on. Unknown age on machine. Fisher and paykel intuitive eco model IW811

Question edited for clarity, turn question around, add CAPS.

It is a motor stall. You need a technician.

Washing Machine - Top Loader Fault Code Numbers

Fisher & Paykel https://support.fisherpaykel.com > article > Washing-M... Sep 30, 2023 - 136, Motor Error - You will need a Service Technician to assist with this - Click Here to ... © Fisher & Paykel Appliances Ltd 2023. Loading.

Questions & Answers for: fisher paykel fault code 136

Fixya https://www.fixya.com > ... > fisher paykel fault code 136 Now Error code 136 means you have a motor stall ... Question about GWL11 Top Load Washer. 1 Answer · What is fault code 136 on fisher & paykel ...

I have a fisher paykel GWL11 that will fill and drain but

JustAnswer https://www.justanswer.com > Appliance Repair May 25, 2017 - If you had a 130 and a 136, the sensor is not likely the issue. Will the tub turn manually? How about lift up and down? Ask Your Own Appliance ...

1 answer · Top answer: Oh, that plastic nut will come off. See the link below. CLICK HERE

https://www.google.com/search?q=Fisher+%26+Paykel+GWL11+top+loader.+Fault+code+136

..

https://householdmanuals.com/fisher-and-paykel/washer/mw512/download?page=4&landingTrack=brand-subcategory

MW511 or 512

Start @ page 33......

https://removeandreplace.com/wp-content/uploads/2016/06/Fisher-and-Paykel-DishDrawer-Service-Manual-DD24-DD60-DD36-DD90.pdf

Best to you

The second light and the seventh light on and beeping is fault 66.
This is info on fault 66.
66. (01000010) Phase 6 - Pressure Transducer (Ptx)
Error - Frequency > 90 kHz
Note: this supersedes Fault code 65 from V41 Motor Control Module
code onwards.
The Motor Control Module has received signals from the water level
sensor (Ptx) above normal frequency values.
Primary Source: Motor Control Module.
Action: Replace Motor Control Module.

it means that the two electronic boards in your machine are out of sync and need to be reset. just turn the machine off at the wall for a minute and then back on. if this doesn't fix the problem, you will need to replace one of the boards, which one is unknown until you try.

The pressure sensor is faulty and needs a new/good secondhand one
You can get one from an old dead board,
But it needs to be calibrated to that board.
To calibrate the new one set machine to fill to low water level,
The plastic hex with red on it needs to be turned up to raise & down to lower the water level.1/8inch of a turn will adjust water by 15 to 20mm.
66. (01000001) Pressure Transducer Error [Ptx Frequency > 90 kHz]
Note: this supersedes Fault code 65 from V41 Motor controller code onwards.
The Motor Control module has received signals from the water level sensor (Ptx)
above normal frequency values.
Primary Source: Motor Control module
Action: Replace Motor Control module

needs a new Rps sensor , 130 is a fualty Rotor postion Sensor

You have fault code 66 (01000010) Phase 6- Pressure Transducer (Ptx) Error - Frequency >90kHZ. In simple terms you need to replace the main "Motor Control Module" Cheers

Hello and welcome to FixYa!
You can get one here:
http://www.fisherpaykelparts.net/index.php?categoryid=115&productid=66

Hope that helps you!

this is a pretty clear cut fault (66). It is a problem with the pressure transducer (water level). The only cure is to replace the motor controller (which is the lower of the 2 modules in the console)