Question about RCA 36V430T 36" TV

Open Question

TV worked fine until tried to turn it on just like normal with the remote. The TV power button keeps clicking, no picture. Seems like the power switch is stuck. It just keeps trying to click on and off repeated. It keeps doing this until I unplug it. Can this be repaired?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Simpson Neal

  • 236 Answers

SOURCE: RCA F20539DG

YOU might have a bad relay or a bad solder connection in the relay control circuit. Sounds like a bad solder joint. Stargazer

Posted on Mar 03, 2007

Ad
MikeNJ1964

Mike Longo

  • 398 Answers

SOURCE: 32" model# F32668

The F32668 uses the CTC203 series chassis and I usually see 2 problems when the set will not run. The first is poor solder joints on a small coil near the horizontal output transistor, but if thats the case the set tends to run for a while and randomly shut off. When the set clicks and never runs I usually find that the flyback (high voltage) transformer has shorted out inside. In this case the flyback should be replaced by an experienced tech.

Posted on Aug 07, 2007

Lashawn Robinson

  • 1153 Answers

SOURCE: RCA Television D52W14

The first thing in this unit is to check the ribbon cable that goes from the front control panel to the back ssb board, I would unplug and replug to make sure seated properly. Then try it again. There are alot of screws to take out but worth it if this solves the problem.

Posted on Jan 08, 2008

poacher1

Adam Phillips

  • 10 Answers

SOURCE: Continuous click noise like its trying to turn on but will not.

I have done some research and found a notorious cap and diode problem with this set. The two 4700uf caps (C14113 and C14115) on the DM1 power board (the board to the left of the sat. box when you look at the set from the back) are under rated and will eventually fail. When these caps fail they tend to take out diode CR14105. This may be your problem. If it is, you can replace the caps with 4700uf 25V 105c and the same as original diode.

Posted on May 13, 2009

Anonymous

  • 147 Answers

SOURCE: When I hit the power button the picture tube does

you are hearing the relay click.the most
common failure with this symtom is the
flyback transformer.

Posted on Jul 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Samsung TV doesn't show a picture, when there was a picture audio and remote not working. Which boards need replaced?


If there is no audio then most likely your main board. If your red power stand by light blinks less than 3 s then its the M/B. If its more than 3 s then its the P/B.

Sep 03, 2015 | Samsung PN50C550 50 in. TV

2 Answers

Lost picture. When using main power button, the


Tries unplug,replug the tv an hour later might work.But this a temp.fix,must replaced the backlight video board sooner or later.

Dec 22, 2009 | Planar PDP-42BK 42 in. Plasma HDTV

1 Answer

How reprogram my universal rca remote control


hold the tv button down and keep it down and then press and hold the power button down and hold them both until the power button stays red then let go of both buttons then keep pressing the power button until the tv turns off and as soon as it turns off press the stop button and it should work.

Aug 31, 2009 | RCA RCR815 Remote Control

1 Answer

Dell plasma 42 inch


fot the most part, you have solved your problem (pow bd), The main bd may also need to be replaced as well. The is a signal upon powering up the system. the pow bd communicates with the signal board. The signal bd, also is responsible for ALL of your additional I/O lines. Between the two of these, + a firmware update, i think the tv will be just fine.

Feb 03, 2009 | Dell W4201C 42 in. Plasma HDTV

3 Answers

JVC 42 inch LCD HD TV has no picture or sound


utencilio posted this fix. It worked for my JVC LT-42X579.

Okay, I found a fix! Called JVC, spoke to somebody there, here it is:
1)unplug the TV completely, no wall no power strips, completely
2)wait 10 sec
3)plug TV back in and Turn it on, the light will still be doing the same thing
4)wait 30 sec
5)ON THE TV, not the remote, locate the menu, volume (-) and power button.
6)while simultaneously holding down the menu and volume (-) button, pressed the power button ONCE and continue to hold the other 2 for 10 sec.
7)on the remote control, go to menu>settings>system info
*** now this I know as a FACT will work on systems that display: JVC - ver.5.32FO001, but I don't know of any other versions***
8)press the mute button on the remote twice
9)unplugg TV again and wait 10 sec.
10) plug TV in and turn on

It SHOULD be working normally now... Thanx to the guys a JVC support for this one, I know it seems like an obvious first place to look, but sometimes it isn't. I for one checked online forums first

Jan 28, 2009 | JVC LT-42X579 42 in. LCD TV

1 Answer

3 in one remote pictured at top of page


I googled the remote name and then when the site came up, scroll to the very bottom and click on "manuals" and the manual that lists all the codes will come up. If you do not find your specific code, try this: turn on your tv, push the "tv" button on the remote, then push the P button in the upper right until it lights twice, then push 991, then push power, and then keep pushing the channel up button until your tv goes off and that is your code.

Sep 01, 2008 | Radio Shack (15-2147) Remote Control

1 Answer

I have a toshiba theatre view 52-54 in.? There is no picture-it seems like the tv is off but the power button light keeps blinking. Tried using remote and button on tv. neither works.


Same problem with mine. I find that if i unplug it and let it sit for about 15 minutes ( let the capacitor drain?) i can plug it back in and it automatically comes back on and works fine till I want to turn it off again and it goes right back to the flashing power light.
I bought an on/off remote for the wall oulet and it makes a great work-around.

May 18, 2008 | Televison & Video

2 Answers

Black Box?


my tv was working fine. somebody hit the menu button on the tv or the remote and i get the black box appearing in the middle of the screen. and also the pip is staying on my tv it keeps showing "a snowy picture of pip sjpwomg channels 2 through 18 i cannot figure out how to get this off of my screen.

Feb 08, 2008 | Panasonic PT-51HX41 51" Rear Projection...

Not finding what you are looking for?
RCA 36V430T 36" TV Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76171 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...