At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
My nordictrack a2250 turns on, the incline works, display works - but even though it shows the belt to be turning at 1 mph - it's not moving and it doesn't sound like the motor is running.
What did you end up doing to fix your treadmill? We're having the same issue with a C1650 model.What did you end up doing to fix your treadmill? We're having the same issue with a C1650 model.
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If the belt on your Nordic Track T12 si treadmill is not running even though the display and other functions appear to be working, there are a few troubleshooting steps you can try:
Check the safety key: Ensure that the safety key is properly inserted into the console. The treadmill will not operate if the safety key is not securely in place.
Reset the treadmill: Turn off the treadmill and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on. This can help reset the treadmill's internal systems and may resolve any temporary issues.
Calibrate the incline: If you recently used the incline function, it's possible that the calibration of the incline mechanism is off. Consult the user manual for instructions on how to calibrate the incline. This process may vary depending on the specific model of your treadmill.
Check the motor and drive belt: Inspect the motor and drive belt for any signs of damage or wear. If the drive belt is loose or worn out, it may prevent the belt from moving properly. If necessary, consult the user manual or contact Nordic Track customer support for guidance on inspecting and adjusting the motor and drive belt.
Lubricate the belt: Insufficient lubrication can cause the belt to stick or not move smoothly. Refer to the user manual for instructions on how to properly lubricate the treadmill belt. Use a silicone-based lubricant recommended by the manufacturer.
Contact customer support: If none of the above steps resolve the issue, it is advisable to reach out to Nordic Track's customer support. Provide them with detailed information about the problem and any troubleshooting steps you have already taken. They will be able to offer further assistance, including potential repair options or guidance from a technician.
You may have a beltand deck problem. Test by the following procedure: without thepoweron stand on the walking belt, push the belt in the, direction it normally turns. If the belt is very difficult to turn (on most treadmill this means that you have high belt/deck friction I first apply silicone lubricant between the belt & deck to see if that clears up the problem. Most problems originate from the belt and deck 75 to 85% of the time
I had the SAME problem, several time, with my NordicTrack A2250 Treadmill.
Allow it to go fully up and then fully down several times, without turning it off. IT seems to "cycle" that way 3 times and then "reboots" itself and starts working normally, again.
I had to figure this out myself... none of the suggestions I read worked.
My Nordic Track Treadmill A2250 is stuck on the 12% incline position and it wont go back down and I have tried to reset it by turning it off, switching the reset button to off and then on or even unplugging it several times. What would be my next move?
Will the treadmill work when the chip is not plugged in, or does it just beep every time you select a button? If so, your problem is easy to solve. The board that supports the two adjacent up and down buttons has slipped. To fix, you'll need to remove the panel and remove the 3-inch retaining bar which is held in my two screws. Realign the board so the buttons are free to move in the available slots. Good luck.
I had the SAME problem, several times, with my NordicTrack A2250 Treadmill.
Allow it to go fully up and then fully down several times, without turning it off. IT seems to "cycle" that way 3 times and then "reboots" itself and starts working normally, again.
I had to figure this out myself... none of the suggestions I read worked.
Try this calibration procedure.
Turn the power switch on. Remove the safety key. Hold the Stop and Speed Up or Speed Plus buttons down then insert the safety key.
The display should show some numbers.
Press the stop key one time and the display should show some other numbers and some 00's. Press the Incline Up button and see if the Incline begins to move, if it does let it go all the way up and then all the way down, wait a few seconds after it stops, then hit the stop key 4 times. It should be calibrated. If it didn't move then the board or the incline motor is bad.
What did you end up doing to fix your treadmill? We're having the same issue with a C1650 model.
×