Kenmore washer model 110.49722990 it will not go into the drain or spin part of the cycle, just sits there and hums, won't do anything. It will fill with water and wash,but thats all it won't finish the cycle.

Probably a capacitor problem, see Amazon.

Whirlpool & Kenmore Washer Won't Spin or Drain, Just Hums

? 6:42
https://www.youtube.com/watch?v=WMvHOtTaTZ4
Feb 26, 2014 - Uploaded by canyonman1963
Whirlpool & Kenmore Washer Won't Spin or Drain, Just Hums - Testing ..... It does not do this every time but about every 3 outof 5 times.

Kenmore Washer Diagnostic - Hums, Will Not Run After ...

? 3:34
https://www.youtube.com/watch?v=C5F-_U0_hYw
Jun 29, 2013 - Uploaded by ApplianceVideo.com
Repair your own Kenmore Washer with these following problems:Hums, Will Not Run After Filling Only at ... Find out why. Close ... Whirlpool & Kenmore Washer Won't Spin or Drain, Just Hums- Testing Capacitor, Waterpump ...

try this
http://forum.appliancepartspros.com/washer-repair/345592-kenmore-90-series-washer-wont-agitate-spin.html
Kenmore 90 series washer won agitate or spin Appliance Repair Forum

You can read about the possible issues that can cause this at the link below. SOLVED Why won my washer spin or drain Kenmore 110 Series Washing Machine

is this your model number here GSC3200ZZ0BL

If it doesn't fill it won't start any other cycle unless you move it ahead yourself. If it hums I am thinking it is trying to fill. Sounds like the valve is turning on to let water in but it is not getting through. My washer has a screen where the hoses go on and sometimes the screen becomes plugging with scale. If that is ok then the solenoid must be coming on but the valve is stuck. Does neither hot or cold settings work? Please rate my answer so I am rewarded points for it.

First, see the Sears parts site for your washer.

http://www.searspartsdirect.com/partsdirect/getModel!retrieve.pd?pop=true&modelNumber=110.23912100

Also see the Whirlpool (Kenmore) Service Manual for top load, direct drive washers.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


The first thing I'd try is using a different cycle. If the washer works as it should, the problem points to the timer.

I'd also check to make sure that when replacing the switch, the connections to the timer haven't come loose.

Since you've replaced the Lid Switch, the motor has power for the drain and spin cycles.

These washers use a reversing motor. The motor turns one way for agitating and reverses for the drain and spin.

Since you cannot hear anything when it is supposed to be agitating, the problem does point to the timer or motor.

No, this is probably a direct drive that has a faulty plastic coupling from motor to transmission. Go to:
http://www.fixya.com/support/r385252-replacing_motor_coupling_W... by jsrock516
Please give him a pat on the back for the help.

When the washer initially fills for the wash, is it only hot water entering the drum? Try switching the water temperature between hot and cold as it fills. If any of them show little or no water getting through, it sounds too easy but check to make sure water supply taps are on, and that the cold/hot fill hoses aren't reversed. Remove the fill hoses and check any of the screen filters for blockage (in the hoses and in the inlet water valve). When the machine stops and waits to fill but all you hear is a hum, it sounds like there is power going to the valve but water is not able to get through it.
Good luck!

My kenmore Model 110 does not go into the spin mode

It's not your exact model but does have some good information about the possible causes.
http://www.shopyourway.com/questions/1099421

If you need further help, reach me via phone at https://www.6ya.com/expert/sean_97e45db9c0ed1da4