Ink cartridge will not reset correctly. stays at left side of printer, will not set to center or right hand side. when it sets to the left, it makes a loud sqeaking/grinding noise. ?????????

Are you using Dell Series 5 ink cartridges?

Please unplug the printer from the wall. Now remove the power brick from the back of the printer for 60 seconds. Now plug everything back in. This will reset any error messages the printer has. Now open the printer with the power on and the cartridges should go to the center to be replaced. Take out both Dell Series 5 ink cartridges and make sure the tape is off the cartridges and insert both back in and make sure the seat properly and latch. Close the printer and it should print an alignment page. If you still get the error message, please read bleow.

Black cartridge = black side(left side) Color cartridge = Color side(right side)

Photo Cartridge = Black side(left side) Color cartridge = Color side(right side)

Dell Series 5 ink cartridges have a sensor in them that cannot be reset. Article on refilling Dell ink cartridges.

Dell Series 5 ink cartridges can be purchased at Staples, Walmart or Dell's Website.

It is also possible to get a new ink cartridge with a bad sensor. Please take it to the place of purchase for a refund or a replacement one.


Rick

Sounds like a bad sensor in the Dell Series 9 ink cartridge.

You are using Dell Series 9 ink cartridges, correct?

Unplug the printer from the wall. Now remove the power brick from the back of the printer for 60 seconds. Plug everything back in. This will reset any error messages the printer has.

Power on the printer. Open the printer and take out the Dell Series 9 Black cartridge. make sure all the tape is off the cartridge and put the cartridge back in. Now do the same for the Dell Series 9 color cartridge.

You are using Dell Series 9 ink cartridges, correct?

Dell Series 9 ink cartridges have a sensor in them that cannot be reset. Article on refilling Dell ink cartridges.

Dell Series 9 ink cartridges can be purchased at Staples, Walmart or Dell's Website.

Black cartridge = black side(left side) Color cartridge = color side(right side)

Photo cartridge = black side(left side) Color cartridge = color side(right side)

It is possible to get a Dell Series 9 cartridge with a bad sensor. Contact the place of purchase for a replacement.


Rick

Are you using Dell Series 9 ink cartridges?

Unplug the printer from the wall. Now remove the power brick from the back of the printer for 60 seconds. Plug everything back in. This will reset any error messages the printer has.

Power on the printer. Open the printer and take out the Dell Series 9 Black cartridge. make sure all the tape is off the cartridge and put the cartridge back in. Now do the same for the Dell Series 9 color cartridge.

You are using Dell Series 9 ink cartridges, correct?

Dell Series 9 ink cartridges have a sensor in them that cannot be reset. Article on refilling Dell ink cartridges.

Dell Series 9 ink cartridges can be purchased at Staples, Walmart or Dell's Website.

Black cartridge = black side(left side) Color cartridge = color side(right side)

Photo cartridge = black side(left side) Color cartridge = color side(right side)

It is possible to get a Dell Series 9 cartridge with a bad sensor. Contact the place of purchase for a replacement.


Rick

Are you using Dell Series 9 ink cartridges?

Unplug the printer from the wall. Now remove the power brick from the back of the printer for 60 seconds. Plug everything back in. This will reset any error messages the printer has.

Power on the printer. Open the printer and take out the Dell Series 9 Black cartridge. make sure all the tape is off the cartridge and put the cartridge back in. Now do the same for the Dell Series 9 color cartridge.

You are using Dell Series 9 ink cartridges, correct?

Dell Series 9 ink cartridges have a sensor in them that cannot be reset. Article on refilling Dell ink cartridges.

Dell Series 9 ink cartridges can be purchased at Staples, Walmart or Dell's Website.

Black cartridge = black side(left side) Color cartridge = color side(right side)

Photo cartridge = black side(left side) Color cartridge = color side(right side)

It is possible to get a Dell Series 9 cartridge with a bad sensor. Contact the place of purchase for a replacement.


Rick

replace the cartridge. make sure when you put it in you place it in all the way and it sets in its slot properly

The encoder strip is most likely the problem. Unplug the power from the printer. Open the front cover and move the cartridge carrier to the center. You should see a white ribbon cable, a thin plastic strip and a black belt with teeth.
The thin plastic strip is the encoder strip. It rides in a sensor on the back of the cartridge carrier that you will not be able to see. Reach in with the first finger of either hand and carefully strum the strip as if playing a guitar.
The strip will need to be lowered slightly and brought towards you slightly. Please be careful not to break the strip or your printer will not function. Once you believe the strip is set correctly, plug the power back and try printing the self test. If it slams to the left again, the strip is not yet set correctly.
If you cannot repair the strip, please let us know so that we can assist you further.

Please Note: Fixing the encoder strip is a delicate procedure. During the troubleshooting, if the strip breaks, you will not be able to use the printer.

There could be 4 possibilities.

1. Ink cartridges lids are open which is not allowing cartridges to move freely.
2. Ink cartridges carriage will not move from its original position(left) when front cover is opened
3. Encoder strip is Dirty.
4. Encoder strip is Out of position.

Solution:
1. Open the front cover and check if ink cartridges lids are properly snapped in.

2. Turn the printer off and pull out the power cable from power socket, open the front cover and manually center the ink cartridges carriage.
Clean the metallic rod inside the printer using WD40 or Kleenex from Left corner to right corner properly.

3. Cleaning the encoder strip:
a. printer should be off and disconnected from power.
b. open the front cover.
c. Using a dry, lint free cloth, pinch the encoder strip on the right-hand side of the cartridge carriage and pull your fingers across it toward the right-hand side of the printer and you can move the cartridges carriage to clean the strip completely.
d. Note: The encoder strip is a narrow band of clear plastic and can be difficult to see without direct lighting running parallel to metallic rod.
e. Close the printer and try again to print.

4. Repositioning the Encoder strip.
a. Remove the power cord from the printer.
b. Open the front cover.
c. Gently slide the ink cartridge carrier to the middle of the printer.
d. Gently move the top part of the printer belt to the right.
e. Using an index finger, gently push encoder strip down and then back up, to get it back into the slot located on the back of the ink cartridge carrier.
f. Gently press the strip first to the rear, and then forward, to ensure that it is seated correctly.
g. Manually move the ink cartridge carrier to the left, then to the right, to check the positioning of the encoder strip.
h. Once the encoder strip has been re-seated, close the scanner lid.
i. Re-connect the power cord to the printer and try again to print.



Incorrect position of encoder strip




Correct position of Encoder strip




Hope it should fix the issue.

Hi,

Did you try disconnecting from the power for a few hours to reset the printer? Also, did you try a waste tank reset?

Issue The printer is working, but the colors in the printed output are not the expected colors. The output may look as if only one color has printed, or as if a color has not printed, or as if the wrong colors have been printed. Solution Complete the following steps to resolve this issue. Step one: Check ink levels If the print defect is minor, it might be caused by reserve mode operation. When the printer runs out of some colors, it can continue printing using remaining inks, but print quality may be affected. If cyan, magenta, or yellow is out, the printer can print only in grayscale.
NOTE: HP cannot guarantee the quality or reliability of non-HP ink. If ink cartridges have been refilled, try replacing them with genuine HP ink cartridges. Replace any empty print cartridges. To access the ink level gauge, follow these steps.

1. Press Setup .
2. Press to select Tools , then press OK .
3. Select Display Ink Gauge and press OK . The ink levels are displayed. Figure 1: Ink levels
   • Each icon corresponds to the cartridge that is the color of the icon. The icons are also in the same order, from left to right, as the cartridges in the printer.
   • If an icon is empty, the corresponding cartridge may need to be replaced soon.
   • The ink levels in non-HP, refilled, and remanufactured cartridges cannot be read by the printer. Instead of an icon, a question mark is displayed for these cartridges. HP cannot guarantee the quality or reliability of non-HP ink. Printer service or repairs required as a result of printer failure or damage attributable to the use of non-HP ink will not be covered under warranty.

Step two: Calibrate the color If the cartridges have not been refilled and none are empty, try calibrating the color.

1. Open the printer Toolbox :
   1. Open HP Solution Center (click Start , then All Programs , then HP , then HP Solution Center ).
   2. If you have more than one printer installed, make sure to select the correct printer tab in HP Solution Center .
   3. Click Settings .
   4. Click Print Settings .
   5. Click Printer Toolbox .
2. On the Device Services tab, click Calibrate Color , then follow the onscreen instructions. The procedure takes about two minutes and requires two sheets of paper.

Step three: Clean the printhead If the steps above did not help, clean the printhead.

1. Open the All-in-One Toolbox :
   1. Open HP Solution Center (click Start , click All Programs , click HP , and then click HP Solution Center ).
   2. If you have more than one All-in-One installed, make sure to select the correct All-in-One tab in HP Solution Center .
   3. Click Settings .
   4. Click Print Settings .
   5. Click Printer Toolbox .
2. On the Device Services tab, click Clean the Print Cartridges , and then follow the onscreen instructions. Three levels of cleaning are available.

Step four: Contact HP If the error still occurs, click the link at the bottom of this page to contact HP.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00707165&lc=en&cc=us&dlc=en&product=1153481&rule=45772