At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The FL code indicates that the door failed to lock when you closed it. Try opening and closing the washer door again. Make sure that there is nothing in the door area that could block the latch or keep the door ajar. If the error recurs, the latch may be faulty.
If the door is actually locked and giving the FL code, the latch has a problem. You can try power-cycling the washer (unplug for a while) or setting the washer to pump the water out. If these steps don't help, you need to order a replacement latch assembly. Depending on your washer model, you may have a manual pull cord to unlock the door. Look under the bleach and fabric softener compartments after opening the dispenser..
I hope this helps. If your washer is under warranty, contact Maytag. Otherwise post a comment with the model number of your machine for a source for a replacement latch assembly.
This is a Failed to Lock Code. Check the seal at the lock to see if something is in the way or blocking it. Overloading or having too many clothes in the way will also cause the door to fail to seat correctly. Generally however the lock mechanism needs to be replaced or reseated as it is no longer making contact with the control board.
Your Maytag Neptune Washing Machine displays error codes, also called "help codes," to identify specific problems with your washer. Once you close your Maytag Neptune's door, the machine locks the door, goes through the selected wash cycles and unlocks the door when the laundry is finished. Error codes appear when there are problems with the door, the inflow and drainage of water and the motor. The "FL" code indicates that the washing machine was unable to lock the door after you closed it. Open and close the door tightly, then restart the washing cycle. Door lock monitor switch in door lock mechanism unable to communicate to control board the door is locked. 1.Check wire connections in harness leading from machine control board to door lock mechanism.2.Check solenoid and door lock enable switch in door lock mechanism. 3.Replace responsible component.
Your Maytag
Neptune washing machine displays error codes, also called "help codes,"
to identify specific problems with your washer. Once you close your
Maytag Neptune's door, the machine locks the door, goes through the
selected wash cycles and unlocks the door when the laundry is finished.
Error codes appear when there are problems with the door, the inflow and
drainage of water and the motor.
Do
Your Maytag Neptune washer displays the "do" help code when the washing machine
is trying to start a cycle, but the door is open or not locked
properly. If this message is displayed, close the door securely and
restart the washing cycle.
FL
The "FL" code indicates that the washing machine was unable to
lock the door after you closed it. Open and close the door tightly, then
restart the washing cycle.
Sd
The "Sd" code indicates that you have added too much detergent to
the washing machine and your laundry has too many suds. The machine
will stop displaying this code if it has successfully run the suds
recovery cycle, which removes the excess suds from the wash load. If the
code remains, reduce the amount of detergent in the load. Use less
detergent for similar loads of laundry in the future.
PF
The "PF" code indicates that a power failure has occurred.
Restart the wash cycle. If the code still appears, check that the
washing machine is still plugged in to the electrical outlet.
Nd
The "nd" code indicates that your Maytag Neptune is not draining
as it should. Check that the drain hose isn't kinked and that the stand
pipe isn't clogged. If you find either of these problems, fix them
before restarting the washing cycle.
LO
The "LO" code appears when the washing machine has finished the
selected wash cycle, but cannot unlock the door. Verify that the door is
closed properly, push the "Off" button, and wait two minutes. The door
should unlock and the error code will disappear. If the error code
remains, unplug the washing machine, wait two minutes and plug it back
into the electrical outlet.
Lr
The "Lr" code indicates that the washing machine's motor is not
running as it should. Have your Maytag Neptune washing machine serviced
by a certified Maytag repair professional.
It appears that the door latch safety interlock was damaged or broken when the door was opened mid-cycle.
The codes "fl" Failure and "do" Door Open, seem to indicate that the latch and/or door switch need to be replaced. I tried to find a drawing and parts list for your washer, based on the model you selected, but could not locate one. If you can get the full model number, you can check for the replacement part at searspartsdirect.com or call them to get the part number.
If you look inside the door of the washer, you can see if the catch (on the moveable door) or the latch, on the washer cabinet) is the broken or damaged.
The repair is relatively straightforward and easy to do, with simple hand tools. Just make sure to disconnect the washer power cord before doing any work on it. Once you've done that, open the door and remove the screws and you should be able to remove either or both, the catch and the latch switch and reinstall the new ones, once you have them.
I unplugged the washer for 20 minutes, plugged it back in, the same FL message appeared, so I slammed the door (as a last effort to attempt to overcome the problem of door failing to close before I would decide to call a repairperson). Following the sound slamming of the door, the washer has worked just fine through the last five loads.
The "FL" is indicating that the door has failed to lock or it locked but the control does not sense the door has locked.
It could be caused by:
faulty door lock solenoid
loose wire connection
faulty door lock switch
faulty door lock sense switch
bad control board
I recommend calling a service technician to diagnose and repair your washer.
but try this first just in case....unplug it for 1 minute plug back in and see if the fault code clears.
good luck.
×