Does not get cold - Kenmore 53502 / 53504 Side by Side Refrigerator

check your temperature sensor near the inlet valve

Its cold start issues:----

Go through the list of help links mentioned below:----

Click the link :----

Cold start problem and vehicle shudder around 2500 to 3500 rpms

http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

----------

Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

--------------

Ford explorer 4.0 will not idle when cold?

http://technoanswers.blogspot.in/2012/02/ford-explorer-40-will-not-idle-when.html

--------

Automatic transmission shift lever hard to move on cold mornings?

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

----------

Car won't start when cold?

http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-when-cold.html

-----------

These will help.

Thanks.

Its cold start issues:----

Go through the list of help links mentioned below:----

Click the link :----

Cold start problem and vehicle shudder around 2500 to 3500 rpms

http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

----------

Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

--------------

Ford explorer 4.0 will not idle when cold?

http://technoanswers.blogspot.in/2012/02/ford-explorer-40-will-not-idle-when.html

--------

Automatic transmission shift lever hard to move on cold mornings?

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

----------

Car won't start when cold?

http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-when-cold.html

-----------

These will help.

Thanks.

Its cold start issues:----
Go through the list of help links mentioned below:----

Click the link :----

Cold start problem and vehicle shudder around 2500 to 3500 rpms

http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

----------

Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

--------------

Ford explorer 4.0 will not idle when cold?

http://technoanswers.blogspot.in/2012/02/ford-explorer-40-will-not-idle-when.html

--------

Automatic transmission shift lever hard to move on cold mornings?

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

----------

Car won't start when cold?

http://schematicsdiagram.blogspot.com/2011/12/car-wont-start-when-cold.html

-----------
These will help.
Thanks.

go to appliancerepairplanet.vstore.ca for a suppot

My bet is that your cold water screen is plugged...

If your washing machine will not fill, only hot or cold will fill or is slow to fill then read these tips. I have covered many of the things that can happen in these tips…


Washing Machine Problems No Water

Washing Machine Fix Washing Machine No Water

heatman101

You need to remove the cover and check the voltage to the cold water inlet valve. Do this with a volt meter while it is set to fill with cold water. It is most likely an AC voltage that is around 24 volts. If you have voltage then the valve is most likely bad.

that's odd.

if you choose cold/cold then check your hose orientation. you could have put the hot water to the cold solenoid.
or the wires have been interchange, the hot water wire was plug to the cold solenoid and the cold water wire was plug to the hot water solenoid.
or hot water is still flowing to your cold water line.

if the cold water solenoid is the problem, then there should be no water at all going to the tub.

try to experiment, try to switch to hot/hot and see what would come out...


tnx 4 using fixya,


drcool

It sounds like you have the hot and cold water lines to the washer reversed.  Try turning off the tap for the hot water then setting the washer to just cold wash and then  hot washif you get nothing on the cold and cold water when set to hot they are probably reversed.  Typically if the auto-temp control is broken you will only get hot or cold coming out on any setting.