I've purchased new blades for my Arctic. they did fine until they got clogged. what can i do to clean my blades? this IS a problem. if i can't find a solution i can't purchase norelco again. please advise

Based on the information you have provided, there are a few possible causes for the issues with your 2011 Arctic Cat 550 EFI. Here are some suggestions for troubleshooting:

Check the fuel injectors: If the fuel injectors are clogged or dirty, it can cause issues with starting and idling. You may need to clean or replace the fuel injectors.

Check the fuel pressure regulator: If the fuel pressure regulator is not functioning properly, it can cause issues with fuel delivery to the engine. You may need to replace the fuel pressure regulator.

Check the air intake and filter: If the air intake or filter is dirty or clogged, it can cause issues with fuel delivery and combustion. You may need to clean or replace the air filter.

Check the throttle body: If the throttle body is dirty or clogged, it can cause issues with fuel delivery and combustion. You may need to clean the throttle body.

Check the ignition system: If the ignition system is faulty, it can cause issues with starting and idling. You may need to replace the spark plugs or coil.

Check the battery: If the battery is weak or not providing sufficient power, it can cause issues with starting and idling. You may need to replace the battery.

It's important to note that these are just suggestions based on the information you have provided..

It's usually the carburetor has clogged jets due to gummed gas (esp. Ethanol). One easy thing to try is to adding Sea Foam to the gas tank and run the engine until the mix is pulled into the carb. Then leave it set for a couple of days to allow the gum to dissolve.

If you haven't changed the plugs that would also be suspect, as John said. Also a new air filter.

It is perfectly fine if the building is cooling and isn't humid. Once the A/C system saps all the moisture out of the air, it won't drip much if at all until there is more humidity. For more info on why they drip and when ... Why is my central air conditioner dripping water

Remove deck belt from blade pulleys and Tri to spin blades by hand. If they don't spin freely, you probably need new spindle bearings but if you do need a new spindle I would replace the whole spindle housing... Just make sure the one (s) you buy has housing, spindle, bearings, nut and washer.

hello sir, mower will not start or run,runs only when primming, does it have good spark,good compression,or only runs on full choke, are you getting fuel to the engine if not try this,your fuel pump or your carb. is clogged up here is what you can do for a simple repair for the carb,you can remove the air filter and assy, empty fuel tank and clean out tank and line,remove the bowl nut and bowl careful of the gaskets,now spray carb cleaner in the small port holes in the carb steam in the middle of the carb until clean,now spray the bowl nut holes until clean there are three,after cleaning put bowl on the same way you removed it with dip towards front of float,put bow, and fresh gas,you should be good to go,hope this helps.,thank you.~~

Possible that the blades are clogged with hair or dirt and the motor is jammed . Use the fine brush that had come along with the shaver to clean and free the blades, Use some light oil on the blades to free any signs of dirt or rust on the blade set.
After shaving it is important to clean and keep the blades dry.

This is a major problem with Arcitec shavers. You and thousands of other have found out too late that the blades can not be removed for manual cleaning. Unfortunately, there is no good solution. You can try running the shaver under hot wateror running the shaver with the heads dipped in rubbing alcol. You can also try picking out the 'gunk' with a toothpick. You will probably only find these to provide minimal results.

If you find that you still must replace the heads, you will fin tham at shaveroutlet.com. See link below

http://shaveroutlet.com/shaver-replacement-parts/norelco-philips-rq10-arcitec-replacement-heads-p-353.html

Have You Checked The Fan/Heatsink Assembly???

Your Heatsink Cooling Fins Might Be Clogged

If So, The Fan Blades, The Heatsink Fins And Assembly Need To Be Cleaned Thouroughly... DO NOT USE COMPRESSED AIR

You Must Disassemble Laptop And Physically Clean these parts

It would be a good idea at this point to also add new Arctic Silver Thermal Paste or Thermal Pads To The CPU/GPU..

why in the world are you replaceing the brush? In 25 years of copiers, i,ve never had to replce a brush. If its streaking on the copy, its the blade thats bad. only reason to replace a brush is if its broke,cause of a clog. just vacumm it out.