Front Load Washer - Error F30

How to Troubleshoot a Maytag Epic Washer Front Loader Tip Call Maytag for service if any of these procedures doesn't clear the code on the washer display.

Warning Maytag makes several models in the Epic series and operating instructions vary. For model-specific troubleshooting instructions defer to the user manual that came with your machine or contact Maytag support.

Each model in the Maytag's Epic automatic clothes washer series has a computerized processing unit that displays error codes on a digital screen when something goes wrong with the washer. These codes help Maytag service technicians diagnose the unit. If you know the codes, you can troubleshoot the problem yourself, rather than request a service call, possibly fixing the issue yourself and saving you some money in the process.
Long Fill (LF) or Drain Problem (F9E1) Error Code 1.Press the power button to cancel the cycle.
2.Unplug the washer or disconnect power to the outlet its using.
3.Turn the power back on and select the cycle you wanted and press start.
Washer Problem (F--E--) Error Code 1.Press power to end the cycle.
2.Open the door to check for excess water in the drum.
3.Press "RINSE DRAIN & SPIN" if there is still water in the drum to remove that excess water.

Suds Routine (SD) Error Code 1.Open the drum at the end of the wash cycle.
2.Remove the clothes from washer, carefully examining them for damage from the excess suds issues.
3.Review your detergent uses to ensure that you're using the recommended type of detergent and the correct amount as stated on the product's instructions.

<https://www.maytag.com/washers-and-dryers/washers/front-load-washers/p.epic-z-high-efficiency-front-load-washer.mhwz600tw.html>
I NOTICE IT READS - TEN YEAR WARANTY ON PARTS.
LINK MAY PROVIDE PHONE CONTACT.

Make sure water supply is active, that hot and cold hoses aren’t reversed, and that screens in hoses and valve aren’t obstructed

The following list of codes indicates an electronics communication problem with the washer: * Epic® washer - F05, F07, F09, F10, F11, F13, F14, F15, F21, F22, and FdU
* Epic ZTM washer - F01, F11, F23, F24, F27, F28, F29, F30, F31, and F33


To remove the error display, press Pause/Off or Pause/Cancel twice.



If Pause/Off or Pause/Cancel does not work:

1. Unplug washer or disconnect power for one minute.
2. Plug in washer or reconnect power.
3. Re-select the cycle and press Start.

NOTE: If the error remains on the display, call for service.

Hope this helps.

I don't know the answer, but you can call Maytag @ call 800-688-9900 toll free for a code definition

ths.gardenweb.com/forums/load/.../msg1012004912002.html

F30 = DISPENSER SYSTEM ERROR
You might have to replace the damaged one.Or in other words something that cannot be repaired.Well came across this info through other certified websites.good luck.hope this helps out.

When someone reports severe vibration during spin on a brand new washer, the first question always has to be whether the transit brackets have been left in.

Washers are designed so that the drum and motor float on a collection of springs and shock absorbers. To prevent damage to these during shipping, a set of brackets is used to bolt the floating assembly to the case. If these aren't removed before first use (the manual will say how to do it) havoc ensues.

The irritating whine is a new one on me.

A.

I need a clear code for maytag epic z front load washer
code f-o1 is coming up
says intall new ccu, I did but still the same
do I need to clear the code if so how.
please tell me.

the control board has loose solder connections around the relays.

see this
diff model same issue with new boards as they make them all.
http://www.fixya.com/support/t364216-whirlpool_duet_ht_ghw9400pl0

being it is in warranty its too early for you to fix it yourself.
you will have to wait for them to come out and say the parts are on backorder.