Question about Kenmore 15864/15862 Top Load Washer

1 Answer

Kenmore Washer Model 110 Movers pulled the bottom apart. Do you have a schematic to reassemble?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,937 Answers

First, see the Sears Parts Site for this washer:

http://www.searspartsdirect.com/partsdirect/part-model/Kenmore-Parts/Washer-Parts/Model-11015862400/0582/0153200?sid=MMLxMerchandizexManualsModelx15862x11015862400

Then see the following for how to tear one apart, you should be able to see what's not in place from this:

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=137&osCsid=0da65cea0e338fe930b1fde153a243f0

Then see the Whirlpool / Kenmore Service manual for top load, direct drive washers:

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf

Between the three sites / documents you should be able to put it back together.

Posted on Nov 21, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's the capacity of the Kenmore Washer Model 110 22692 100?


Kenmore 110 Series Washing Machine series washer capacity is 3.2 cu. ft. - Kenmore 110 Series Washing Machine

Kenmore Washer Model 110 22692 100 specs Google Search

Oct 09, 2018 | The Computers & Internet

1 Answer

Kenmore washer Model 110, Serial No. 27602690 won't spin


If wash cycle operates and water drains as should before spin indicates motor spinning. Chances are bad timer If your a real fixer you can remove timer control from panel check and clean all contacts internally making sure none are stuck closed . (Have had 3 110s in my time).not easy but can be done or buy new about 150$ reassemble and check operation.

Mar 28, 2013 | GE WBSR3140DW Top Load Washer

1 Answer

The contact button (part where you put the door down to make the washer start to agitate) something came apart....washer is filled with water and now won't go. The part came out.


you broke the lid switch,send the full model number located under the lid,lift the lid up,follow the lid to the bottom and look right under it and you'll see the model number,it will start with like 110.

Aug 30, 2011 | Kenmore 22422 Top Load Washer

1 Answer

Kenmore heavy duty 70 series model 110-8237012


probably your drain pump leaking it has a seal right where it attaches to motor,,,,mine is leaking there but haven't replaced it yet! lol

Feb 27, 2010 | Kenmore Washing Machines

2 Answers

Top-load agitator removal


The agitator on most Kenmore top loaders is a split design. The upper portion is called the auger, the bottom is the agitator. It comes apart by followng these simple steps:

1. Remove the center cap on the auger by either pulling straight up or gently placing a flat blade screwdriver into a slot located in the cap. Make sure you keep the gasket. This is used to create an air gap to keep water from leaking into the transmission, so make sure you seat it properly for a good seal when you reassemble.

2. If the auger is equipped with an inner cap underneath with a handle, remove this as well by pulling straight up.

3. Remove the center bolt of the agitator. You will have either a 7/16” hex bolt or a recessed square plastic nut. If you have the square recessed type, use a 3/8” to ½” ratchet adapter to remove.

4. With the center bolt removed, you can remove the entire assembly with the auger still attached to the top of the agitator, by grasping the bottom flange near the bottom of the tub and carefully pulling straight up. Try to keep all the parts assembled while doing this, so do not pull too hard. This will make this reassembly much easier.

If the agitator comes apart and you need assistance in how the parts go back together, refer to searspartsdirect.com for some helpful exploded view diagrams under the "Agitator, Basket and Tub" parts section.

If you have any questions, or if your agitator is different from what has been described, please post back with your complete model number (located on a nameplate around the wash tub opening) so that I may be able to provide you with better assistance. I hope this helps you.

Oct 20, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore washer model 11026912691 magnetic latch assembly


I have to assume that you mean the "Lid Switch"

See the following Sears parts site for your washer.

http://www.searspartsdirect.com/partsdirect/getModel!retrieve.pd?pop=true&modelNumber=110.26912691

Look at the sub-component section on the top and cabinet and you should be able to see how the switch connects.

If you cannot tell from the schematic, I' d use the Whirlpool number for the switch (peobably 8054980) and go to dome of the on-line washer parts dealers for a better look. The Whirlpool parts site doesn't have pictures of their parts.

Oct 11, 2009 | Kenmore Washing Machines

1 Answer

Washer wont spin or take out the water


Hi 1st remove cabinet by removing 2 screws securing the console to the cabinet top.pry clips at corners and remove .you should now be able to pull cabinet towards you and separate it from chasis .motor /pump at center front bottom.plastic plug on right, wiggle that plug with washer in spin probably bad connection in plug.red/black wire Hope this helps please rate my solution. :)

Jun 26, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 110 washer


if screens on both ends of cold fill hose are clean replaced valve have seen restricted flow even with good flow to valve but be sure screen in valve is pulled and cleaned be sure to reinstall it

Aug 01, 2008 | Kenmore 22422 Top Load Washer

2 Answers

Reassembly help


try kenmore website for 800 customer service number

May 23, 2007 | Kenmore 94702 Front Load Stacked Washer /...

Not finding what you are looking for?
Kenmore 15864/15862 Top Load Washer Logo

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5692 Answers

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...