Where can I purchase a Canon i9100 waste ink pad?

Hi, please get new driver here: www.driversdown.com/
www.nodevice.com/driver/company/Canon/Printer.html
www.usa.canon.com/cusa/office/products/.../hs_1200ts

Jay bcfxt

CANON WASTE TANK RESET CODES

Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA iP3000 above,
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

Reset Procedures for Canon i560 Printers

1. Turn off i560 Printers
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your Canon i550, i560, i850, i860, i865, i9100, i9950 Printers should respond as normal.
9. Please remember at some time of other you will need to clean out the ink pads that are inside the printer.

Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

Hi
You can try this I found.

Reset Procedures for Canon i9100 Printers

1. Turn off Canon i9100
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your Canon i9100 Printers should respond as normal.

Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

Here you go:
http://www.fixyourownprinter.com/forums/printer/46473

Ink that leaks out of the ink-cartridge when the print-heads are "parked" is absorbed into the "reservoir" tank. The tank is full. Get it emptied.

Inkjet printers have a fibrous pad inside them that collects the waste ink from cleaning the print head. Over time, this pad fills up with ink and can no longer hold any more. When this occurs, the printer indicates a "waste ink tank full" error.

The waste ink absorption pads are inside the printer, in the very bottom. They are usually soaked with ink when full and are very messy.

Replacing the waste ink absorption pads is something an authorized canon service facility can take care of for you.

Hi!
The printer counts every single droplet ejected by the print head due to waste ink absorber capacity. When the waste ink counter rise to about 90 % the printer shows message 'Waste Ink Absorber Near Full'; in this stage we can still continue printing by pressing Resume button until waste ink absorber capacity reach 100% and 'Waste Ink Absorber is Full' appears.
To fix this problem you have to reset waste ink counter to 0%. Even though we can just reset waste ink counter without resetting waste ink counter, it strongly recommended that you replace waste ink absorber to prevent ink flooding inside the printer.
To reset waste ink counter, perform the following steps:

• Plug in power cable
• While pressing Resume button press and hold Power button (do nor release the buttons)
• Release Resume button (still hold Power button)
• Press Resume button twice in a row (still hold Power button), after that release both Resume and Power button (then the printer standing bye)
• Press Resume button 4 times then turn off the printer

In this stage your printer has operated as usual.
Regards,

this is the webpage where you can download a couple of manuals for your printer.
Quick Start for Canon i9100 is the manual you want to download registered free and download (try using a fake email address if you want.. and see if it lets you) http://www.retrevo.com/support/Canon-i9100-Printers-manual/id/259bh537/t/2/
it has maintenance instructions that should let you take care of your needs.

Inkjet pads are between the printer chassis and the bottom of the printer case. Typically a large felt pad.
My Canon i9100 has eight orange flashes and indicates on screen "waste ink tank is full". After opening up mine I found this to be false, only one third soiled. This then leads me to believe the i9100 has a timer to go off after a preset number of hours.

Anyone know how to reset the "full waste ink tank" error?