I own a samsung GT I 9000. Have been trying to synchronize with my corporate mail server without success in spite of following the screen tips. Could you please help me or atleast guide me to a custormer relation executive to whom I could talk to resolve the problem.

This is from Microsoft:-

If you receive Server Error: 0x80048849 and/ or 0x80048820 in Windows Live Mail at home or while you're in your regular network, it may be due to the setting of the MTU (Maximum Transmission Unit) on the mail client.
If you get this synchronization error at a coffee shop, airport or a place from where you don't usually connect to the internet, we suggest synchronizing mail on your regular internet connection.
When the MTU setting on the mail client is larger than the MTU settings configured on network devices between your mail client and the mail client servers, some data packets may be lost, causing mail synchronization to fail.
Follow the steps given below to fix synchronization errors due to mismatched MTU settings:
Determine the MTU setting on your network device
Apply the MTU setting to your mail client
Determine the MTU setting on your network device
This is a trial and error process, and will be different for each user. You may have to repeat the procedure below a few times, before you can find out the MTU setting of your network device. Follow the steps below:
Open command prompt
Click Start ? Run ? Type cmd
In the Command Prompt Window, type in the following:
Ping <Mail server address> -f -l 1500
Notes:
The <Mail server address> is the IP address of the mail server that you are unable to synchronize with.
For Hotmail, 65.55.33.106 is the IP address for DeltaSync (mail.services.live.com).In this document we will be using this IP address as an example.
In the -l 1500, 1500 is the max MTU for Ethernet connections.
You may get an error like this (100% packet loss):
C:\Users\username>ping 65.55.33.106 -f -l 1500
Pinging 65.55.33.106 with 1500 bytes of data:
Packet needs to be fragmented but DF set.
Packet needs to be fragmented but DF set.
Packet needs to be fragmented but DF set.
Packet needs to be fragmented but DF set.
Ping statistics for 65.55.33.106:
Packets: Sent = 4, Received = 0, Lost = 4 (100% loss)
If you received the error above, subtract 28 from the 1500 bytes of data. In the Command Prompt Window, type in the following:
Ping <Mail server address> -f -l 1472
If you get a 0% Packet Loss with 1472, it means the MTU setting of your configured network is 1472
Note: If you continue to receive the error described in (b) above, repeat the above steps by subtracting 28 from 1472 bytes of data. Repeat these steps until you get a message for 0% packet loss. If you were able to communicate with the mail server at an MTU size of 1424, you will receive the following:
C:\Users\username>ping 65.55.33.106 -f -l 1424
Pinging 65.55.33.106 with 1424 bytes of data:
Reply from 65.55.33.106: bytes=1424 time=230ms TTL=241
Reply from 65.55.33.106: bytes=1424 time=196ms TTL=241
Reply from 65.55.33.106: bytes=1424 time=162ms TTL=241
Reply from 65.55.33.106: bytes=1424 time=163ms TTL=241
Ping statistics for 65.55.33.106:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss)
Approximate round trip times in milli-seconds:
Minimum = 162ms, Maximum = 230ms, Average = 187ms
Apply the MTU setting to your mail client
Follow the steps below:
Open command prompt as administrator (you must be an admin on the computer)
Click Start ? Run ? Type cmd
In the Command Prompt Window, type in the following:
netsh int ip show int
You will receive a message similar to the following. Find the connection name that you use to connect to the internet and note the Idx value
C:\Users\Username>netsh int ip show int
Idx Met MTU State Name
--- ---------- ---------- ------------ ---------------------------
1 50 1472 connected Loopback Pseudo-Interface 1
11 20 1472 connected Local Area Connection
To apply the correct MTU setting on your mail client, type the following in command prompt:
netsh int ip set interface <Idx value> mtu= <MTU setting of your router> store=persistent
Press Enter
For example, if the correct MTU setting was 1424 and Idx value of your connection was 11, you will type:
netsh int ip set interface 11 mtu=1424 store=persistent
If (c ) was successful, you will receive the confirmation message "Ok"
Exit command prompt
Restart your computer
Open WL Mail and see if the issue persists.
have Windows Vista Home Premium Recently unable to send or recieve Window...

It may be a server problem or setting problem. if you have technical knowledge than

• Go to Mail >Preferences >Accounts >Outgoing Mail Server SMTP >Edit SMTP server list.
• Change server name> smtp.macmate.me and save .

here you also change your password as well. but if you are not aware about technical detail than follow Apple Support Number .

I have successfully set this up using yahoo.uk mail.
I cannot get it to work with gmail or virgin mail.

Use these settings:


pop/smtp email server > smtp.mail.yahoo.co.uk
send to email address > your email address
account > your email address without the "@yahoo.co.uk"
password > your password


You can forward emails to your normal email address so that you can get alarms on your mobile without adding another email account.


Unfortunately your computer needs to switched on with sec24 running.

Q: How do I set up corporate e-mail?



A: This setup enables you to wirelessly synchronize your email and other information directly with the information stored on a Microsoft Exchange Server.


From the programs menu, tap Accounts.
Tap Add account.
Tap Corporate Sync.
Enter the domain, username, pass-word, e-mail address, and server for your Microsoft Exchange e-mail account.
Tap Next.
Note: Contact your company's IT department if you need more help. This feature works with Microsoft Exchange e-mail servers

Hi Dear ....
The mail configuration is very simple on any smart of Os version phone. But you must have a configuration knowledge. Follow the mention below instruction of config the Yahoo Mail in GT -S5570

1. Open your Yahoo Mail in laptop\computer and go to the "Option" select the "Pop & Forward" and check mark in "Enable you yahoo mail Pop-up"
   
2. Go to your mobile and open "Social Mail" if its not there then choose the "Email"
3. Type you Email Address and password and click the "Next".
4. Wait for few second its verified and synchronize to Yahoo Server.

If you get any other "Error" please let me know....


Thanks to Visit on Fixya...

Once you've got a serial console attached you can access the CFE which is a bit like the bios of the WGT634U. Start up minicom and apply power to the router while holding Control C. You should see something like the following:

CFE version 1.0.34 for BCM95365R (32bit,SP,LE)
Build Date: Tue Feb 24 03:21:41 CST 2004 (root@jackylinux)
Copyright (C) 2000,2001,2002 Broadcom Corporation.

Add MAC client version(DNI).
Initializing Arena.
Initializing Devices.
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller
CPU type 0x29007: 200MHz
Total memory: 0x2000000 bytes (32MB)

Total memory used by CFE: 0x81BB1280 - 0x82000000 (4517248)
Initialized Data: 0x81BB1280 - 0x81BB3E90 (11280)
BSS Area: 0x81BB3E90 - 0x81BB45D0 (1856)
Local Heap: 0x81BB45D0 - 0x81FB45D0 (4194304)
Stack Area: 0x81FB45D0 - 0x81FB65D0 (8192)
Text (code) segment: 0x81FB65E0 - 0x81FFFFB0 (301520)
Boot area (physical): 0x01B70000 - 0x01BB0000
Relocation Factor: I:E23B65E0 - D:01BB0280

configure vlans
*****************************************************************
*********************** VLAN Driver initial ********************
*****************************************************************
Process LAN port(2-5) vlan Architecture...
SUCCESS: trying to create VLAN 0 for switch
SUCCESS: trying to add LAN port

Process WAN port(2-5) vlan Architecture...
SUCCESS: trying to create VLAN 0 for switch
SUCCESS: trying to add WAN port
SUCCESS: enable ports success
configure vlans...done
Automatic startup canceled via Ctrl-C
CFE>
Now you can get a listing of the available commands by typing "help". If you want to boot a kernel from a tftp server do the following:

CFE> ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0;
CFE> boot -z -elf -tftp 192.168.1.10:vmlinux.gz
Or you can automate the process by setting STARTUP using:

CFE> setenv -p STARTUP "ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0;boot -z -elf -tftp 192.168.1.10:vmlinux.gz;boot -elf flash0.os:"
The router will now try and retrieve a kernel image called vmlinux.gz using tftp from 192.168.1.10. If this fails it will go ahead and boot the kernel on the flash. The is quite handy as in conjuction with a NFS root, it means you can do all your development without modifing the original firmware.

OTE : VERY FIRST ENABLE POP3 FROM YOUR GMAIL ACCOUNT SETTINGS. LOG IN TO YOUR GMAIL ACCOUNT > ON TOP RIGHT CLICK ON SETTINGS >THEN CLICK FORWARDING & POP3 > THEN ENABLE POP3 FOR ALL MAIL OR YOU CAN SELECT OTHER OPTION. BUT AT LEAST POP3 MUST BE ENABLED. THEN SAVE CHANGES. POP3 Gmail Settings For Samsung Star Cellphones:
Go To > Menu > Messages
Click Settings > Email
Then Touch >Email Setup Wizard
Notice will ocuur Touch > OK
Give name to your account E.g Gmail
Enter your email id : [email protected] , Then Enter Password for your account.
Incoming Server type : POP3

Incoming Server : pop.gmail.com
Outgoing Server SMTP : smtp.gmail.com
Secured Connection : Off
Then touch OK & it will display your POP3email account configured successfully. Now press back button and tap on Email Accounts, then touch the email account you have just created. There some more option than above you just have to edit that.
Secured Connection: Off
POP3 Port: 995
SMTP Port : 587
Now, Tick The option APOP Login.
Download Limit: 500
Secured connection: SSL (Choose SSL for second option only & not for first option.)
Retrieving Option: Choose Subject only
Keep On Server: Tick
My Address: yourname @gmail.com
Username /Password : same as you entered above
POP before SMTP : Dont Tick
SMTP Auth: Tick
Same as POP3/IMAP4 : Tick
And Finally Save All Settings.
That's it !!!, Now you can retrieve your message from your mail box & Click on Download to download all messages.


If you want your Samsung star phone to automatically download your messages ? Here is a small option they have given for that.
Go To Message > Settings > Email > Receiving Options
Download Limit: 300KB
Auto polling: Home Network Only
Following option is time after when email is downloaded automatically.
Polling Frequency: 30 Minutes (you can choose higher if you want)
Send read report: Tick
And again your emails will be automatically recovered from server at every 30 minutes. And you'll get notified near your message notifier on your home screen if there is any unread emails.

Hi, it seems that the DNS is not taking you to the desired website. You can run a command "ipconfig /flushdns" from command prompt without quotes. (Start Menu -> Run ->cmd). Once done try to check the website once again (http://mail.yahoo.com/). If you are not able to open the website again, I would recommend you to reset your internet browser. Hoping that you are using Internet Explorer as your internet browser, open Internet Explorer, then click on Tools -> Internet Options -> Advanced Tab ->RESET. Follow the steps to reset your Internet Explorer. You can alternatively do it from Control Panel -> Internet Options ->Advanced Tab ->Reset. Once done successfully, you will be able to open your websites smoothly.
Cheers!

Try again make this settings my friend

The Mail tab is where you send and receive e-mail messages. Including Outlook E-mail, you can add up to four POP3/IMAP4 and web-based e-mail accounts in this tab.
To add an e-mail account
1. On the Home screen, slide your finger to the Mail tab.
2. If this is your first time to add an e-mail account, touch New Account on the bottom-right side of the screen.
3. Set up your e-mail account using the E-mail Setup wizard.
4. To add another e-mail account, touch Menu > Accounts > New Account and use the E-mail Setup wizard to set up your account.
For detailed instructions on setting up e-mail accounts using the E-mail Setup wizard, see Chapter 6.
To check e-mail
When there are new e-mails, the icon on the Mail tab and the respective icons of the e-mail accounts will show the number of newly received messages.





If you have installed the synchronization software on your computer and created a partnership with your device, then your device is ready to send and receive Outlook e-mail.
If you have not yet installed the synchronization software nor created a partnership, do so by following the procedures in Chapter 5.
Tip To set up your company e-mail account so that you can access Outlook e-mail messages wirelessly, you must set up your device to synchronize via an over-the-air connection with your company’s Exchange Server. For more information about synchronizing with your company e-mail server, see Chapter 7.
Add an e-mail account
To add a new e-mail account, you can do one of the following:
On the TouchFLO 3D Home screen, slide to the Mail tab and then touch Menu > Accounts > New Account; or
Tap Start > Messaging > Setup E-mail.
The E-mail Setup wizard then opens and lets you enter your e-mail account settings. See “E-mail Setup Wizard” in this chapter for details.

Start ActiveSync on your 9502 and set it to synchronize with an exchange server. Give your e-mail address, and, if required, the server URL 'm.google.com', and your login credentials to gmail. Follow the screens and make sure you check the box to synchronize your e-mail. By clicking on some 'advanced' hyperlinks (blue colored) along the way, you will be able to set e.g. if you want to receive all the messages currently on the server, or from the last 3 days only, attachments handling, synchronization schedule, and other settings.
Hope you are able to do it without problems.
Cheers! Carlos