Same problem, but now it is ok. I emailed Sunbeam and was told that if my blanket was not plugged directly into a wall outlet it was not getting enough power and I needed to plug it into a wall outlet taking these steps:
1) Unplug from the surge protector/extension cord
2) Unplug from the blanket
3) Plug back into the blanket
4) Plug into a wall outlet
There cannot be a surge protector or plug extender on the same outlet as the blanket plug. Additionally, once you unplug the blanket plug you have to wait a full 5 minutes for the system to reset before plugging it back into the blanket. :).
It sounds like there is a wire in the heating coils that is weak or broken, if it's a broken wire, it's junk, you can't cut them open and re-splice them, and that's what your problem sounds like, a broken heating coil.
Thats useless. Dont have a wall socket it can plug directly into. Power point is on other side of room
Thats useless. Dont have a wall socket it can plug directly into. Power point is on other side of room
×
My electric blanket blinks only on one side and I can not turn it off what di I need to do?
YEAH! Unplug from the wall . wait 10 seconds, HOLD DOWN POWER LEVEL SELECTOR BUTTON & plug back in! Set on LoW 10 minutes , pray & Go*
My sunbeam electric blanket also blinks and I cannot turn it off. ??.
Unplugged from wall outlet, then unplugged from bed. plugged back into wall outlet then back into the bed...works fine now.
Russ is right shave off a little on the bottom i did an it works thanks alot russ
I have just encounted the same problem one side works the other side blinks have tried every thing and its still wont work way to go sunbeam create blankets that make us cold
In all honesty get a different blanket..my pad did the saem thing and I received a 2nd degree burn across my belt line.
Checek the internet, and you'll see how many suits have been filed against Sunbeam for the same things as far back as 2003.....might be worth getting rid of the blanket
I've had nothing but trouble with my electric blanket. One side doesn't work and now the other keeps blinking. I've tried the methods to stop it and nothing works. Extremely disappointed with this product. Never buying a sunbeam again.
I bought mine 1 week ago. Nothing but blinking lught. I cant seem to have it on anything more than 3 setting or light blinks snd blanket turns off. The shop is getting a replacement for me. After reading all this going to ask for refund. Antone know a decent electric blanket that works. Sonetimes its really cd and id like to have heat higher without it just switching off. Shop said it would be controller. This is ridiculous.
×
First, we had a Sunbeam that lasted 8-years - now we have boughtTHREE
different blankets (all Sunbeam) and could not get any of them to
work (permanently) Lights stay on, F-2 is on and unplugging and
starting over only lasted a few hour and we were back to the
same proglem - will try to find a different brand
Well for those who still get the blinking light on the controller, make sure the plug that goes into the blanket is pushed in....all the way! Then voila! No more blinking light.
None of these troubleshoots work. I tried all of them. I'm really angry and disappointed. I need the heat because it helps with RA pain. now I won't be able to sleep comfortably. it is a washable blanket. I followed the instructions. make a better, sturdier product, Sunbeam.
Blanket keep blinking can’t get it to work
I have tried all of these and my blanket controller still blinks and my blanket will not heat up. It's new and never been washed or anything I just got it for Christmas
This is the kind I have
This is the same plug we have and it is only a couple months old and already blinks red. Very frustrating as we live in Oregon and live a warm throw when it works
That's what mine is doing. I am so disappointed. This is my second one. I'm not taking this one back. Going to toss it and never buy Sunbeam again.
×
What I did was this.....
1. Unplug from the wall and from the bed spread.
2. Wait 30 seconds then plug into the wall but not the bed first.
3. Then plug into the bed correctly, there is a wrong way.
4. then on main controller hold the power on button for ten seconds then let off.
5. Then on second controller hold power button for ten seconds then let off.
6. That is a hard reset and now should work accordingly.
Tip.
Do not use a surge protector.
Do not use an extension cord.
Do not run cords in between box and main mattress. Instead run underneath the bed.
Do not allow cords to become pinched in any way.
Enjoy
Well if id known that i woumdnt have bought it. I dont have a wall socket i can plug directly into. Their cord is nowhere near long enough to reach. Most people use extension cords. Only lately have houses been built with more than 2 outlets in every room. I live in a house that is over 70 years old. One wall socket in each room so multibox and extension lead is tge only option available
what "2nd control"???
×
Unplug at wall, reconnect shpould do it. It must have "read" between wall and blanket plug that interferes with be boot, so just kill power throughout entire line, restart good luck, works for me twice now.
59,229 views
Usually answered in minutes!
Same problem. When I turn either of the dual controls on any heat setting, within seconds it starts blinking, quits heating, and all control is lost at that point including turning it back off or changing the heat. The only solution I've found is unplug it, but as soon as you plug it back in and turn the blanket back on, same thing all over again. I've checked plugs, cables and all I see that could be checked. Nothing helps.
same problem.Control lights blink and blanket does not work anymore.Only used it for a month.
Happens to me too.
I am having the same problem with a Sunbeam blanket. It it a single control fill size. The control is blinking on and off and will not respond. I tried the suggested hatd boot routine of unplugging from the main, unplugging the blanket from the line, re attaching and then re plugging into the main (wall outlet) Control seems to be restored.
Mine just started blinking too. I have dual control. We checked everything we could check. We unplugged it from the wall and it didn't help. We couldn't figure out how to unplug it from the blanket. We have had it for only 3 months. We are just not using the side that blinks. Are you still using yours?
Same problem. Dual control - one side works, other side blinks and does not heat. Have only been using it about a month. Way to go Sunbeam.
I have a fix for your electric blankets, the problem is it is not fully plugged in at the foot of the blanket. You must engage the plug past the point where it connects and snaps together. If it still does not work you might have to modify the plug. Just save off a little on the bottom so it will side further in and then you will have a good connection. It worked for me hopefully it will work for you.
Russ
My new dog chewed the end of our 4 prong controls to our Sunbean electric Blanket. . .Just looking to buy a new 4 prong end or just a dual control unit. Where do I find this?. . .I tried everywhere. .
I have the same problem..
Exactly the same problem. I have also tried all of the above solutions without success. Nothing works.
Exactly the same problem. I have also tried all of the above solutions without success. Nothing works.
Exactly the same problem. I have also tried all of the above solutions without success. Nothing works.
i had the same problem. we washed our heated blanket and hung it up to air dry. once it was dry we tried plugging it in, and the light on the controls just kept blinking on the highest setting. i tried everything to get it working again, i checked the connection on the module, i unplugged and plugged it back in at the wall plug-in. i couldnt get it working even i clearly followed the washing instructions according to the label correctly. Eventually i got so frustrated with it that i just gave up, unplugged it and walked away. However a little later i decided to go back and check it again, just in case, and all of the sudden it starts working again! It was a pain but im glad it started working again at least.
Same deal but only one side works. The other side keeps blinking
It sounds like there is a wire in the heating coils that is weak or broken, if it's a broken wire, it's junk, you can't cut them open and re-splice them, and that's what your problem sounds like, a broken heating coil.
Did not work for any of my 3 blankets poor quality will not buy anything else made by Sunbeam. We are out of almost $200
None of these troubleshoots work. I tried all of them. I'm really angry and disappointed. I need the heat because it helps with RA pain. now I won't be able to sleep comfortably. it is a washable blanket. I followed the instructions. make a better, sturdier product, Sunbeam.
It sounds like you are having trouble with your Sunbeam electric blanket controls. When you plug the control cable into the blanket, the controls blink but you are unable to turn them on or off. This may indicate a problem with the connection between the control cable and the blanket or a malfunction with the controls themselves. You may want to try unplugging the control cable and plugging it back in to see if that resolves the issue. If not, you may need to contact Sunbeam customer support for assistance or consider purchasing a replacement control.
Click here if you want to know Electric Blanket Light ON But No Heat. Why?
×