Have changed (new) batteries - it turns on - works - and cuts out dead after 10 seconds

the dash lamp IMMO will not lie, it tells you if the key is good or now, covered in the free users guide.
but use the IMMO can lie of battery is near dead. sure.
not told what the gear shifter does,
what does CUT ON mean? (radio dead or works/)
the steps are easy cart like this auto transmission
we can crank the engine in park or neutral if we step on the the brake pedal, the lever moves. at your demand, called park lockout feature
I get it ,does nothing means the starter is 100% dead
while key turned (cranking) in PARK.
turn the key to on /run position the IMMO lamp talks to you now, it tells 2 things key good or key bad
if bad no immo car will ever start. or starts for 1 to 10 seconds and stalls.
if the battery is dead or failing many things will word and not work, for example radio works but the starter is dead the starter uses 1200 times more power than the starter.. so radios can work. with near dead batteries.
for 70 years true.
so, check battery lugs for rusty or loose
charge the battery and load test it.(in a shop)
or buy the tools.
or jumper cable jump the battery.
or call AAA auto club tow,and say jump start me car.

also learn that IMMO can lie to you if battery is weak.
answering for NO CRANK cars.

new water pump, ,
did old pump/engine overheat?????????
not getting gas I guess you meant only that the engine is dead?
or the starter motor is dead. not told evidence. all.
if engine good, gas is last
spark if first after engine good.
the PCM even cuts fuel if spark is detected dead.
so check for spark !
did you remove battery cables before this work.?
then put them back last?
we do that to prevent blowing up fuses or worse.
my guess (wild ESP) the engine cranks fast but will not start.
or stalls or runs 10 second and stall or never starts
and spark is dead.

I needs service,get some?

• immo lamp not happy on dash/ engine Immo can cut spark 1 t010 seconds from start. bad key (ignition)
• fuses blown
• scan the PCM yet to see all those DTC errors?
• low fuel pressure.
• spark plugs never changed (they are bad 17 years old)
• head lamps dead is , alternator bad. (as battery dies)

engine there new.

• 2.4 L 2AZ-FE I4
• 3.0 L 1MZ-FE V6
• 3.3 L 3MZ-FE V6
• 3.5 L 2GR-FE V6

best is diagnose HL head lamps dead. they work bright key on and key off, tell more about HL actions first.

does the starter motor sound strong each time you starter the engine ?
when it runs for 10 seconds ,during the run
does the IP cluster lamp glow (charge/battery.GEN) ,yes ALT is dead.
or a battery cell shorted.

If the battery is dead, the first thing to do is get your battery charger out and charge the batteries up. Nothing works without battery power.

Firstly, pop a new battery in the fob.
Now we can enter the EKA.
Close all the doors.
Turn the key in the driver door lock to the unlock position and hold there for at least 5 seconds until the alarm sounds once. Then return to centre - always ensure you return to centre and do not delay more than 10 seconds between turns, or hold in the position for more than 5 seconds or you will reset to the start. Turn to full extent of travel.
1st Digit turn to unlock the number of times specified.
2nd Digit turn to lock the number of times specified.
3rd Digit turn to unlock the number of times specified.
4th Digit turn to lock the number of times specified.
Finally turn to unlock once more. If it is correct a double bleep will sound (single bleep is incorrect code)
You now have a 5 minute delay - don't open any doors. The anti-theft indicator will continue flashing once every 2 seconds for the five minute period. When this goes out, open the door and start within 30secs.
After 3 failed attempts, the security system invokes a delay period of 10 mins during which the system will not accept any further attempts to enter a code.

Ita an imobilizer fault.Try changing the key fob battery first.Before having it reprogamed.

You are ok with what you got. The cordless saws take a lot of power to cut wood so it drains the battery fast. I have the ridged setup and my battery on a full charge only gets 4 cuts on a 2x4 befor it is dead. The saws will not give you any worning becauase the teath of the blade will get stuck in the wood so it just will not slow down like the drill will. I hope this helps with your ?

It's the processor or power supply. I cant be sure of which without checking it.

Check the fan over the processor heat sink to make sure its working cause it could mean that the processor is overheating If the fan turns and then it cuts off this could meant that the processor is dead. or the bios is corrupted. Try flashing the bios, there is a battery on the main boad, remove it. unplug the system first... when the battery is out press and hold the power button for 10 seconds then release. put the battery back in and try to turn it on..

If that fails then try a new power supply or one from another system to to check if the power supply is fine. YOu can aslo bridge the green and any black wire from the power supply's mainboard connector to see if the power supply runs. If all this fails then you may need to replace your processor,, I';d also recommend changing the power supply as well.

I also bought an aftermarket battery for my F707 on Ebay and got the same "for info...." message.
I contacted the seller and they sent me a new one and it worked, don't see a way around it.

poncha,
Your battery might be dead and it might cause problem to boot.

• Remove battery, insert A/C adoptor and try to boot normally, if success then you should change your battery and all will be fine. If no success then try next step.
• Remove battery, remove A/C adoptor. Press and hold power button abt 10 seconds then insert A/C adoptor holding the power button on. Keep holding for 30-45 seconds. If still no success then have a tour to the service centre.

Thanks & Good Luck
Iqbal