My scales i turn it on and the number keep going different and there is nothin on it

Hi,

I've found your manual on two different website but I'm unable to link them here. Please contact weight watchers and ask them to email you the manual for your weighing device so that you calibrate the device or factory reset it in order to weigh properly. The manual is only 2 pages.

Try setting up your scale again, following the instructions found int he first section here: http://www.taylorusa.com/faq-scales

I have a Health-o-meter but not the same model. Mine still has the instructions pasted (loosely) to the bottom.
The secret is that you must initially press the lower (left or right side) corer for just a second or two. That causes a few dashes and then the scale reads 00.0. Then get on the scale and get your reading.
Alternative behavior:
If you initially press the corner for more than a few seconds it will cycle through User Numbers one through four. If you use that feature it remembers your weight from the last time so you can see the difference.

No different than setting one that turns clockwise. You set it in so the rotor on the distributor shaft lines up with the number 1 cylinder spark plug tower on the distributor cap, and then you follow the firing order around in a counter clockwise direction.
This will get the distributor set right, as long as you have the number one cylinder at Top Dead Center of the compression stroke before you drop the distributor in.
To find TDC of compression stroke, pull the number one spark plug. Turn the engine over by hand with a socket on the crank pulley-turn it clockwise-or you can have someone bump the starter over in short bursts. With your finger over the spark plug hole, turn the crank over until you feel air pressure build up in the cylinder. Now look at the timing pointer scale next to the crank pulley. Keep turning the crank until the notch or mark on the crank pulley lines up with the zero degrees mark on the pointer scale. The air pressure behind your finger tells you that you are on the compression stroke. When the crank pulley notch lines up, you are at TDC of the compression stroke. The piston will be at the top of its travel. Now you can drop in the distributor. Keep playing with it until you have the rotor pointing directly to the number 1 spark plug tower. The shaft will turn a little as it is dropped in, so you start with the rotor a little ways back from directly to number 1.

WHO makes it and can you find a photo of yours online? A search for your model number shows MANY possibilities!

Turn it over - take out battery and check with multimeter to ensure it is still workable - let sit for 10 to 15 seconds - replace battery - set it on level surface and step on and back off. Step on it again and it should now work.

Hi,
you need just to recalibrate it:
The procedure is standard for semi-all models of pocket scales, but the way how to get to calibration mode differs from model to model (or vendor to vendor).
In brief:
1.While turn-on get to the calibration mode (by pressing and holding the ON button, or holding TARE while turinig on) You should hold this "magic" combination until the LCD will show a number (large number - it was more than 2000 in my case). This number is a raw data from the sensor.
2.Now release the "magic" button.
3.Press it one more time, the display will show 2Ero and then 100.0
4.Now put calibrated weight of 100 grams on the scale and wait 3 seconds.
5.Press "magic" button again.The display will show CAL and then PASS.
6.Now remove the weight and turn off the scale.
7.Thats all - now you can use your scale as usually.

sounds like you got a bad egg i got that same phone with sprint and it works great ,.if you just got it just get the warrenty number and they will replace it for free.,,......,,,,,,

To totally reset the scale and remove any old data in the users take battery out for 2 hours.

To use the USER functions:
Tap scale to turn it on
When you see "0.0" press
Press SET button. "P-1" will appear and blink
Use UP/DOWN button to select a user number
once desired user number (1-4) appears press SET button to confirm

when 0.0 appears step on scale this will enter your starting weight
press SET to confirm
scale automatically sets a goal weight of 10% below starting. you can raise or lower it by using arrow buttons-Press SET to confirm

Tracking weight
tap, see 0, select user number. Scale displays start weight, then goal weight then 0.0 and you weigh yourself. In the smaller windows it will display last weight and the difference between current and last weight then diff between current and start then diff between current and goal

Can you use scale away in the Tefal Aquaspeed 260?