Question about Maytag MHWZ600TB Front Load Washer

2 Answers

Maytag Epic Z MHWZ600TB01 Only Runs In Spin Mode. My Maytag front-loader will only run spin cycles. When I press the "start" button on any wash cycle, the power to the unit turns off. I used to reset this condition by setting the cycle, but not starting it, and then letting it sit until it timed out and turned itself off again. Then it would work fine. Now that doesn't reset it and I can only run spin cycles. Someone had this same problem in http://www.fixya.com/support/t3953494-maytag_epic_z_start_except_spin_only and I need a more definitive answer as to how to fix it. If there was a loose or broken wire - where is it?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,796 Answers

Hi!!
Click on the following link for a diag. of the control panel. to get access to the back of the Control Board http://www.searspartsdirect.com/partsdirect/partsdirect/showSubComp.pd?imageUrl=http://c.searspartsdirect.com/lis_png/PLDM/W0901032-00003.png
check that wiring harness (#8) connections to the Electronic Control Board are tight and the wiring is not broken, burned or damaged. Disconnect the Unit and feel the wire harness (#8) for any small bumps or deformities, repair as needed.

Good Luck! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa!!

Posted on Feb 21, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 1 Answer

I have a Maytag epic z front loader model # MHWZ600TB01 it reading to much suds I clean it out but how you take the hose and coin trap and the other piece that is connected to right of the long drain pipe

Posted on Dec 08, 2019

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I push the power button and when I hit start it just shuts off. The only cycle that works is spin on my maytag epic z


Any luck? the certified Maytag repair company looked at mine and quoted $445. for the repair. it is 15 months old so of course the warranty is obsolete. The solution is a new CCU panel and Temperature sensor. Good luck.

Aug 30, 2011 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

Maytag Epic front load washer spin cycle sounds like an airplane is taking off


If you mean a jet aircraft, that is normal. Front loaders achieve amazing spin rates.

Feb 14, 2010 | Maytag MAH2400A Front Load Washer

2 Answers

Won't spin or drain, have tried to rerun cycle and checked drain hose


Check pump / outlet filter , refer to instruction book , clean and replace then re- try

Nov 01, 2009 | Maytag Neptune MAH5500B Front Load Washer

2 Answers

Maytag Epic Z Washer has object between drum and tub.


I had the same rattling during spin cycle of my Maytag 4000 series front loading washer. Noticed you could gently pull back on the rubber gasket between the tub and where the door seals. There was a quarter resting against the fixed ring the tub spins in. Problem solved. And I have further realized that long hair can build up in this same spot. But if you didn't know to pull back on the gasket you wouldn't see it. Good luck!

e58c8277-9a05-4a0b-ba6b-e8db67caaa33.jpg


20190816_083801-apy0hbzx41yu0zsjevfqwy5c-3-2.jpg

Jun 23, 2009 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

My new Epic Z is only one month old


sounds to me like there is a short in the wiring or control board i would call the warranty company to come fix it

Dec 30, 2008 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

Maytag washer wont start spin cycle...


INSPECT YOUR PUMP HUMMING NOISE USUALLY PUMP MOTOR ARE PRETTY RELAIBLE

Nov 29, 2008 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

Maytag front loader MAH-3 vibrates. Level & on concrete floor.


THERE ARE SHOCK ABSORBERS IN THIS UNIT,SOUNDS LIKE ONE OF THEM IS BROKEN.HOPE THIS HELPS

Nov 16, 2008 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

Maytag Epic


the control board has loose solder connections around the relays.

see this
diff model same issue with new boards as they make them all.
http://www.fixya.com/support/t364216-whirlpool_duet_ht_ghw9400pl0

being it is in warranty its too early for you to fix it yourself.
you will have to wait for them to come out and say the parts are on backorder.

Feb 04, 2008 | Maytag EPIC MFW9700S Front Load Washer

Not finding what you are looking for?
Maytag MHWZ600TB Front Load Washer Logo

1,534 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...