Sqeeks when you step on the belt; mainly on the right side. Also bell hangs up, sometimes almost coming to a stop, especially at low apeeds.

Don't know Veritas 8 from fleabitis ape, sorry very much

http://www.youtube.com/watch?v=qgb2TY3WCkg&feature=related (NOISE MOTOR)

Watch this videos tips:
http://www.youtube.com/watch?v=qgb2TY3WCkg&feature=related
http://www.youtube.com/watch?v=-oeXTKqWECw&feature=related
http://www.youtube.com/watch?v=GPI6dFJCUA4
http://www.youtube.com/watch?v=bF3OyQ3HwfU&feature=related
http://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitness
http://www.fixya.com/support/r10786838-test_procedure_dc_motor

Remember you bought second hand machine, you must shure about the main motor if o.k . By that reason Test carefully with the videos and tips, if the motor is faulty or controllmer motor, +belt drive(faulty), and Inspect for lubrication.

i`m guessing that you are trying to find out which belt is making the noise.first you need to push on each belt to see if the belts tight and not to loose,at the same time check the sides of the belts for a glaze or shiny sides as well as cracks in the belt .any belt that is to loose may just need to be tightened, any belt that is glazed or cracked needs to be replaced.if the condition of the belt is good then it probably just needs to be tightened.a trick to find which belt that maybe just loose enough is to take a wax candle or a bar of soap and with the engine running(being very careful around moving components) take and apply the wax to each side of the belt one belt at a time, when the noise stops that is the belt that needs attention either by replacement or tighting

answer the door.. lol..pull plug on the door bell....unscrew the ringer and remove the wiring from the door bell...the door bell switch is stuck.

open the top let it laid back look down to top right and left sides you will see two srecw take them out and the front shound come off.but first take the bottom off you will see a tension pulley lose it to take the belt off .then take the tumbler out

does it squeek like a whistle if so you may need to change one of the belts in the engine either alternator or timing or even fan

Well, first restart your computer and see if it does the same. If it does follow the next steps: -right click on My Computer; -Manage; -Services and Applications; -Services -Look for the services that contain audio in their name and especially for Windows Audio. Right click on it. Go to Properties and check the start up method. Put it to automatic. Stop and Start the service again.
If you need further assistance, leave a comment. Cheers

if the pick wheels are just hanging down you need a bell crank for the auto-compensator this part is 56p1228 turn the printer onto its back this plastic piece is known to break. look to the right its located on the end of the long shaft comming fron the auto compensator and if its broken there should be a spring either in the tray of still hanging from the mount

check the pulley bearing if it's an older belt try cleaing the **** out of it
usualy serp belts collect small particles and lodge them in the grooves it will squeek if **** in groves

Hi sharonwoods:
Try these steps,i hope this helps you.

This is caused by an unseated or unlocked transfer
belt.
1. Open the top cover and check that the transfer belt is
properly seated and locked in position.
■ Reseat and re-lock the transfer belt.
■ If the fault recurs replace the transfer beltt.
2. Check the condition of the transfer belt harness
(especially if replacing the belt does not resolve the
problem).
■ Reseat or replace the harness if defective.
3. Check the signal on Pin 1 (CN10) on the main board.
■ Replace the main board if the signal is low.