Why won't my vision fitness simple T9500 run? I tried holding down the stop button for 3 seconds. It did clear the screen. Then when I hit start it puts 6000 in the screen and will not run. It beeps as if...
With the safety key in place, press and hold “ELEVATION UP” and
“SPEED DOWN” for 5 seconds. The software version will appear in
display window shortly before model number appears. Press “ENTER”
to accept correct model number IF YOU CANNOT GET INTO CALIBRATION EITHER UPPER CONSOLE ELECTRONICS OR OVERLAY CONSOLE ASSEMBLY HAS FAILED.
• Press “STOP” to enter “ENG1”. Press “ENTER”.
PLEASE NOTE: HR Window = “0” for miles, “1” for kilometers, treadmill will
calibrate in kilometers if set for kilometers.
STEP 2 MINIMUM SPEED
• Press “ELEVATION DOWN” button, “P0” will appear in display.
• Press “START” button, the running belt will begin to move at minimum
speed.
• The display window should read approximately “.49 - .51”.
• To adjust, press “SPEED UP” or “SPEED DOWN” buttons, the range
should be “.49 - .51”. Press and hold “ENTER” to save changes. Press
“STOP” to return to “P0”.
STEP 3 1/4 SPEED
• Press “ELEVATION UP” button, “SP1” will appear in display.
• Press “START” button, the belt will move 1/4 speed.
• The display should read approximately “2.71 - 2.73”.
• To adjust, press “SPEED UP” or “SPEED DOWN” buttons, the range
should be “2.71 - 2.73”. Press and hold “ENTER” to save changes. Press
“STOP” to return to “SP1”.
STEP 4 1/2 SPEED
• Press “ELEVATION UP” button, “P1” will appear in display.
• Press “START” button, the belt will move at 1/2 speed.
• The display should read approximately “6.72 - 6.73”.
• To adjust, press “SPEED UP” or “SPEED DOWN” buttons, the range
should be “6.72 - 6.73”. Press and hold “ENTER” to save changes. Press
“STOP” to return to “P1”.
STEP 5 3/4 SPEED
• Press “ELEVATION UP” button, “SP2” will appear in display.
• Press “START” button, the belt will move at 3/4 speed.
• The display should read approximately “9.41 - 9.43”.
• To adjust, press “SPEED UP” or “SPEED DOWN” buttons, the range
should be “9.41 - 9.43”. Press and hold “ENTER” to save changes. Press
“STOP” to return to “SP2”.
STEP 6 MAXIMUM SPEED
• Press “ELEVATION UP” button, “P2” will appear in display.
• Press “START” button, the belt will move at maximum speed.
• The display should read approximately “12.10 - 12.12”.
• To adjust, press “SPEED UP” or “SPEED DOWN” buttons, the range
should be “12.10 - 12.12”. Press and hold “ENTER” to save changes. Press
“STOP” to return to “P2”.
STEP 7 MINIMUM ELEVATION
• Press “ELEVATION UP” button twice, “P4” will appear in display.
• The display should ready approximately “190 - 205”.
• To adjust, press “ENTER” for value which should read “190 - 205”. Use
“SPEED UP” or “SPEED DOWN” buttons. Press and hold “ENTER” to
save changes. Press “STOP” to return to “P4”.
STEP 8 MAXIMUM ELEVATION
• Press “ELEVATION UP” button, “P5” will appear in display.
• The display should read approximately “750 - 765”.
• To adjust, press “ENTER” for value which should read “750 - 765”. Use
“SPEED UP” or “SPEED DOWN” buttons. Press and hold “ENTER” to
save changes. Press “STOP” to return to “P5”.
REMOVE SAFETY KEY TO EXIT ENGINEERING MODE
REPLACE SAFETY KEY AND PRESS START TO TEST TREADMILL
×