Question about Kodak EasyShare Z612 Digital Camera

2 Answers

Menu button does not work

Appears I'm not alone with this problem. How do I get the menu button to work? Thanks for your help.

Posted by on

  • dirkkrisn Sep 21, 2008

    menu button does not work

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had the same problem and fixed it! There is a small resistor just to the left of the menu button that was misaligned in theproduction process and the slightest amount of shock(i.e. small drop or maybe even bumping the camera with your hand) wouldbust the resistor's connection loose.
I basically just pulled the cover off, removed the old resistor and bridged the two points and that fixed it.

I am putting a more detailed HOWTO on the front page of my site, you can view it without making an account, but feel free to if you want. I hope this helps a few people.

http://HouseOfChaos.gotdns.com is my site, I also took a few pics and should have them up tomorrow.

Cheers,
ChaosReigns

Posted on Sep 29, 2008

  • Seriago Oct 04, 2010

    It worked for me too. Although I was not able to 'bridged the two points' where the connector use to be, I carefully laid a small flat head screwdriver to bridge them temporarily and then pressed the (internally) menu button to access it and tell the camera to only use the internal memory when no SD card is in.

  • Betamail One Dec 30, 2011

    I Followed your instructions and it worked perfectly, great advice Thank you very much.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 34 Answers

Try cleaning it with a soft cloth, press it severel times or try shake it a little bit.Anything pointy (not metal) would help u clean the button.As a last resort I recomand disassambing the part with the button, but that could be tricky...

Posted on Sep 01, 2008

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a LG 19EN33T-B and it works well with windows 8 but when I upgrade to windows 10, the monitor couldn't be connected to my pc. Why?


win 10 up grades are causing problems
it is better if you get win 10 and instal it as a stand alone rather than an upgrade

Jan 29, 2017 | LG Computers & Internet

1 Answer

The FUNC button in the D80 does not work


In the menu settings, you need to assign the Func button to do something. The Func button alone will not operate until you assign a task. The tasks available are listed in the menu setting for the Func button.

Aug 09, 2014 | Nikon D80 Digital Camera

1 Answer

Have purchased some cartridges (compatable) for my Oki C5600 but i am unable to use them to to microchip.Is there a reset method or do i need to buy more chips?


Reset the Drum Counter:
a. Press the MENU 1/Menu 2 button while turning the
printer on.
USER MNT appears on the display.
b. Press the MENU 1/Menu 2 button until the message
corresponding to the drum you are replacing
appears. For example, if you are replacing the
magenta image drum:
MAGENTA DRMCNT
RESET
c. Press the ENTER/POWER SAVE button.
RESETTING briefly appears on the display.
d. Press the ON LINE button.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

May 25, 2011 | Samsung OKIDATA - OKI C5200n - Printer

1 Answer

Nokia XpressRadio 5030 phone keypad is not working properly, problems as follows. 1) top right button does not show go to menu but shows digit 8 and disappears 2) Clicking on 2 digit number appears 23...


  • if phone has history of getting dropped to the floor or banged hard, this could cause the keypad contacts to misalign
  • try opening the case and cleaning the keypad contacts
  • best solution is have it checked by nokia service center tech support

Oct 02, 2010 | Nokia XpressRadio 5030 Cell Phone

1 Answer

PC locked up during/after ipod nano sync


are you using iTunes 8
version 8 is the buggiest version of iTunes yet.
I don;t think your alone with your problem.
Try putting you ipod in disk mode before you sync it.
to do that, Press and Hold the Menu and Center buttons until the Apple Logo appears on the screen.
Then quickly move your fingers to the Center and Play/Pause buttons until a check mark appears on the screen.
Connect it to iTunes and see if it helps,

Also, you may want to run a spyware program on your computer. you can find a free one at http://www.lavasoft.com/
often times when you get a bunch of spyware and junk in your computer it will act like your problem.

May 27, 2009 | Apple iPod touch

1 Answer

OSD Main Menu appears randomly and uncontrollably /flashing. Power Button does not always work. Need to keep clicking unti works.


hello..the problem is just sticky tack switch's so try to clean or re-align the frame/body of LCD..Thanks.Good Luck..^_^

May 08, 2009 | Dell E207WFP LCD Monitor

1 Answer

Dell 924 all in one will not print magenta


run a nozzle clean, perform the following steps:
  1. Verify the All-In-One Printer 924 is powered on and connected to a computer.
  2. Verify that the paper support (input tray) has clean, plain white paper loaded.
  3. Press the Menu button.
  4. Press the Down button until Mode: Maintenance appears on the LCD screen.
  5. Press the Menu button.
    The Dell 924 Maintenance Menu appears on the LCD screen.
  6. Press the Down button until Clean Cartridges appears on the LCD screen.
  7. Press the Start button.
    The AIO 924 prints the cleaning page. This process cleans the ink cartridges and resolves many print quality issues.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Nov 19, 2008 | Dell 924 All-in-One InkJet Printer

1 Answer

HP 1530 Onscreen Menu refuses to go away


the button is bad on it the select OSD button
the cable is bad, and tells you out range, no signal, or other cable dead errors or in sleep mode. can be PC, cable or monitor
id have to see your screen to wax smarter.

unplug monitor from power and pc
let sit for 1hr.
the plug it in all alone
does OSD pop up> is there an error
if no error there, the monitor buttons are broken,

Jun 10, 2017 | HP L1530 (Carbonite, Silver) 15" LCD...

2 Answers

E173FP flat monitor


Try pressing and holding the menu button for 15 seconds! That should unlock the controls! Regards, babb

May 08, 2007 | Dell E173FP 17" LCD Monitor

8 Answers

TURN OFF PROGRESSINE SCAN ON ZENITH XBV443


Cause: DVD+VCR was turned off while setting the Progressive scan mode. Correction: Keep pressing the STOP button for more than 5 seconds.

Oct 16, 2005 | Zenith XBV443 DVD Player/VCR

Not finding what you are looking for?
Kodak EasyShare Z612 Digital Camera Logo

Related Topics:

663 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Cameras Experts

Ekse

Level 3 Expert

13434 Answers

Vitally Alcher

Level 3 Expert

1645 Answers

FIKRET UNALIR
FIKRET UNALIR

Level 1 Expert

239 Answers

Are you a Kodak Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...