Question about LG Washing Machines
Symptom Error Codes
Sub Symptom LE error code
Question Locked motor error code.
Answer LE error code: This indicates a locked motor condition. Please check the following conditions. Large loads of laundry can put a strain on the motor causing the LE error code. Try removing some clothing and restart. Excessive suds can cause the LE error code. Make sure the customer is using an HE (High Efficiency) detergent. They should decrease the amount of detergent until the machine washes without suds. A few bubbles can be expected. Areas that have �soft� water will usually need to use less detergent. If you suspect that excessive suds are the problem, let the machine stand for 30 min (motor cool down) and then run a rinse and spin cycle before restarting the load. If these directions are followed and the code persists, the machine will likely need service. .
Posted on Aug 17, 2008
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: What does an
Thanks for using FixYa. Make sure the error is not IE, which means water has not reached to the pre-set level within 4 min. since ERROR inlet valve operated or water has not reached to the normal level within 25 min.
The 'LE' error message indicates the control board has detected that the motor is either not turning, or has locked up for some reason. Monitoring the motor is the job of the Hall Effect sensor board which constantly determines the direction and speed of the motor and feeds that information back to the control board. If there is a problem between what the motor should be doing and what the hall effect sensor says the motor is doing, the 'LE' will be displayed and the cycle will be stopped.
Motor lock can be caused by several things from a loose connector, to a bad motor, or even the hall effect sensor failing or dislodging from it's mount. Any one or more of these components could have caused this error, but it is possible to separate the working from the non-working, just by following a process.
To make sure its not a locked motor, try turning the drum with your hand. And, if you feel some resistance while turning the drum or the drum doesn’t move freely then the motor is locked and you’ll need to get it replaced.
The hall sensor is rather easy to replace, and is covered by a seven year part warranty (in US). Take the back cover off. Take the big nut off and remove the motor rotor. Remove the bolts holding the motor windings. Remove the electric plug on the sensor and unclip it from the motor winding. Snap new sensor on and reassemble. Usually takes under a half hour.
Also check for ---
Please do rate the solution and revert for further assistance.
Posted on Nov 12, 2009
SOURCE: LE fault code on LG
Hi from retired Englishman in SW France,
LG's 'LE' stands for 'Lock Error' indicating that there is a problem either with the door lock or the door locked sensor requiring a service call, sorry ;-0(
If this has assisted and/or clarified the situation for you please consider a 4 thumbs up on our rating.
Thanks and good luck!
Posted on Sep 24, 2011
Tips for a great answer:
Sep 13, 2016 | Kenmore Washing Machines
Jun 23, 2015 | LG Washing Machines
Oct 07, 2014 | LG WT5070CW 4.7 Cu. Ft. Ultra Large...
Feb 05, 2018 | LG WM2277H Stainless Steel Front Load...
May 04, 2017 | LG TROMM WM2688H 4.0 cu.ft. Front Loading...
Sep 24, 2011 | LG Washing Machines
Nov 27, 2009 | LG Washing Machines
Aug 27, 2009 | LG Washing Machines
May 31, 2009 | LG WM-2077C Front Load Washer
Feb 15, 2020 | LG Washing Machines
1,991 people viewed this question
Usually answered in minutes!