I need the button that under it says "Press to

no parts like that are not a stock item
for the price , junk it and get a new one

get the iron hot. Take a piece of fabric and a dryer sheet. Put the dryer sheet between two layers of fabric. Place this at the edge of your ironing board. With the iron hot, run the sole place over the "fabric/dryer sheet set" several times. This will remove wonder under and many other adhesives from your iron.

Hi,
Increasing the temperature setting can ease this issue, however it is important to consider the type of fabric you are ironing.

1st option: Fill the iron up, and let the iron stand as the iron heats for little while before using. This may allow more of the water to be converted to steam.

2nd option: You could try using deionised/distilled water in your iron.

If you find that the water leaks out sporadically, it may be worth pushing the steam button once or twice before applying it to clothing.

I have attached a link with a little bit more information How to Stop Steam Iron From Dripping

Try running a mix of water and vinegar through your device to clean the steam pathways. you can also try C.L.R the same way.

do this

If the iron heats but steams improperly, inspect the soleplate and clean the vents (see below) and flush sediment out of the steam chamber (see below).
If the iron produces too much or too little heat, test the electrical cord . Also test and, if needed, adjust calibration of the thermostat
If the iron does not spray properly, inspect and clean the nozzle (see below).
If the iron leaks or spits, clean the steam vents, nozzle, and tank.
If the iron sticks to fabric, clean or repair the soleplate. If the iron stains fabric, clean the soleplate, clean the tank with a commercial cleaner, and use distilled or filtered water.

see this steps and fix it. God bless you
f the iron heats but steams improperly, inspect the soleplate and clean the vents (see below) and flush sediment out of the steam chamber (see below). If the iron produces too much or too little heat, test the . Also test and, if needed, adjust calibration of the thermostat .
If the iron does not spray properly, inspect and clean the nozzle (see below).
If the iron leaks or spits, clean the steam vents, nozzle, and tank.
If the iron sticks to fabric, clean or repair the soleplate. If the iron stains fabric, clean the soleplate, clean the tank with a commercial cleaner, and use distilled or filtered water.

How to fill your Sunbeam Steam Valet
Here is how you fill your Steam Valet. Press the small button on the back of the handle and pull bottom of handle apart from the top half of steam valet. Then take off the white cap on the inside of the handle and fill with water to top. Place cap back onto the opening and slide handle back and click in place. Plug in and you're ready to steam within a few minutes. If it spits out water let heat up a little longer if that doesn't stop it then tie a thin cloth over the top part where steam comes out to keep the water from spitting out onto your fabric. Hope these instructions are clear enough. More questions about this iron go to www.manualslib.com.

Right below the button that you press to select fabric is that black rubbery piece. Use a screw driver to pry it up and then remove the three screews holding down the rest of the retracter. Mine was getting power to the circuits so I trashed it. I won't ever buy this brand iron again has it did not last very long.

good luck

I'm sorry, I could not locate the exact part you need, but try this link. http://www.sharkclean.com/cgi-bin/livew/site.w?location=olc/contactus.w&frames=no&target=main&sponsor=000001There is a number to a representative who could probably help you out. I hope this helps.

Most likely it is the fuse that regulates the heating element on your press that has burned out.
All you have to do is open the top, remove the heating plate. The fuse will be on the left, button shaped.
Replace the fuse and put everything back together and the unit should work.
You can buy a fuse from the company you bought your press at or contact the manufacturer.