Error code " du "

An F/dL error code indicates a problem with the door lock. The error code will pop up when the door fails to lock. The washer will display the error code after six attempts to lock the door. To fix the issue, the door lock assembly needs to be inspected for loose or broken wires and other signs of damage.Oct. 4, 2021

How to Fix Whirlpool Cabrio Washer Error F - Appliance Express

https://applianceexpresstx.com > News and Tips

Whirlpool Cabrio washer error code f

https://all-errors.com > whirlpool-cabrio-washer-error-c...
What Is the F Error Code Related? ... The single F error without additional letters, signs, or numbers indicates the failure of the control board. It cannot send ...

Troubleshooting Whirlpool Cabrio Washer Error Codes - The ...

https://www.thespruce.com > Electrical > Appliances
Oct. 5, 2021 - F then 1 flashes when there is a primary control failure. Replace the machine control assembly. ... F then 2 flashes when the washer is in:.
Fault Code: Washer Problem
UL(none): Unbalanced load
LF(F30): Long Fill
DU(F83): Door Unlock Failure

Whirlpool Cabrio washer error code F

https://washingcodes.com > whirlpool-cabrio-washer-er...
What is the F error code? Basically, this code indicates main control or program faults, which make the work of your washer impossible, as the system loses ...

unplug it for an hour and read the manual

Door unlock error. The machine tried 6 times to unlock the door. Must be an item of clothing jamming the door. take the bottom panel off and reach up and grab the emergency ring, GENTLY release the door amigo. Use this GUIDE for repairs
and use your tech sheet inside that base panel for error codes and diagnostics.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

That's a door unlock error. The machine will display that code when after trying 6 times to unlock the door, it still won't unlock.

The DU in the display is an error code for the door lid not unlocking. This is an indication that the lid lock assembly has failed or the control board is unable to determine if the lid is unlocked. This usually indicates that the lid lock assembly will need to be replaced.
http://www.servicematters.com/maytag_library/docs/16007803.pdf
Service manual above.

The Kenmore Oasis and Whirlpool Cabrio washers are essentially the same. Following is the Whirlpool Installation and service manual for their Cabrio washers.

The DU indicates a problem with the door Un-lock mechanism. See the section on troubleshooting and display codes.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/409753510a90c8be852571e90073421b/$FILE/8178583.pdf

that code is for the door unlock error. is it possible that you may have tried really hard to open the units lid when it was locked? if so the door lock may have been broken. if not, then try to unplug the unit for a few minutes and try a new cycle.
if the code comes up again then you will have to call for free service as it has a 1 year warranty for parts and labor. yes even if you broke the lid lock!!! dont worry it happens when you get something new and are not sure how it works.

brand new and you changed the latch mech.? door latch or lock asm.? DU is door unlock error, it tried to unlock and cant. usually replace lock asm (inside machine) for this problem. may have latch out of alignment.

Just in case there is a pull string with a loop, all plastic under the latch, need to pull the toe panel off and reach up inside the right, unplugged of course until you feel the switch. a pull latch is below the switch incase this happens and hats off to all star/ a serial error or a faulty switch is most of what causes this to start.

The du error code relates to door/lid that cannot unlock. Check that there is no excessive weight on the lid. In case this is not the issue, you should check the lid switch unit. Good luck !