It has power, turns on then immeiately clicks off?

Sustain board fault. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/

hi there,

Check for bad solder on convergence module. May have bad stk's. Do not neglect looking for bad solder on dsignal and defl boards. Mitsubishi is very prone to bad solder.

`jack

Check you Bore piston.
Have you been using your bike with low oil, then check your bore immeiatly and refill oil

is it overheating?

Acer notebooks with the Windows operating system installed give computer users the ability to set power-saving options. For example, with Standby or Sleep mode, the computer will turn off certain battery-consuming features and save all open files in memory. If Hibernate is enabled, after a period of time, the computer will turn itself off after it saves all open files to the hard disk drive. You may save time in troubleshooting by first verifying the settings that control how your notebook powers on and off.

1. Press the "Power" button to turn the computer on and recover from Hibernation or open the lid of the Acer notebook to awaken it from Sleep mode. If your computer does not power up, continue.

2. Click the "Start" button, click "Control Panel," and then click "System and Security."

3. Click "Power Options" and then click "Change plan settings" on the "Select a power plan" page.

4. Click "Change advanced power settings" on the "Change settings for the plan" page.

5. Double-click "Sleep" on the "Advanced settings" tab and then double-click "Sleep after."

6. Click one or both of the "On battery" or "Plugged in" options and then click the arrow.

7. Click "Never" and then double-click "Hibernate after."

8. Click one or both of the "On battery" or "Plugged in" options and then click the arrow.

9. Click "Never" and then double-click "Display."

10. Double-click "Display" and then double-click "Turn off display after."

11. Click one or both of the "On battery" or "Plugged in" options and then click the arrow.

12. Click "Never," click "OK," and then click "Save changes." If you still experience problems, visit the Acer website and check if updated drivers are available for your Acer notebook. The link is listed in References.

I hope you find it very helpful. Thank you for using fixya.

Also,Follow the procedure to reset the waste ink tank counter:

1. Turn off the printer ( "Power" button).
2. Hold the button "Resume" (red circle in the triangle), turn on the printer (click "Power") - an indicator light green.
3. Hold the "Power" button, release the button "Resume".
4. Not releasing the "Power" button, double click "Resume" and release both buttons.
5. Four times click "Resume"
6. Once you click "Power", to confirm the selected action (reset counter absorber). Click "Power" button again to turn off.

Follow the procedure to reset the waste ink tank counter:

1. Turn off the printer ( “Power” button).
2. Hold the button “Resume” (red circle in the triangle), turn on the printer (click “Power”) – an indicator light green.
3. Hold the “Power” button, release the button “Resume”.
4. Not releasing the “Power” button, double click “Resume” and release both buttons.
5. Four times click “Resume”
6. Once you click “Power”, to confirm the selected action (reset counter absorber). Click “Power” button again to turn off.

The Evo N610c is upgradable to only 1GB of memory. You're overloading the motherboard, it can't handle 2GB. If you really need 2GB, get a new laptop (or a PC, for that matter). Otherwise, I'd run (2) 512MB sticks of RAM to even out the workload.

tv wont turn on when i hit power it makes the clicking noise like it is going to turn on, but never does and the red timer light next to the power button just flashes.
help!
trinitron kv29f1u
only clicks and blinks

Sounds like sass virus. try using Avast Free
download run and schedule boot time scan.
the registration is free and they will e-mail you a reg. code.