AEG Cooktops - Popular Questions, Answers, Tips & Manuals

The igniter is not working and should be replaced and there is also a problem with the igniter as well.

even look on google https://www.coolblue.nl/en/advice/zanussi-aeg-induction-cooktop-error.html

not sure as to what you can do , if it did get too hot, maybe wrong pan, but could also be wrong temp in unit, only way to find out is to try and use warrenty

Refer to your installer/supplier. The unit has a fault in one of the controller boards that needs to be replaced. It may well be done under warranty.

p1 beep sound

prestige induction cooker showing error p with beep sound problem solution

did you get it fixed?

Hello mons_sorense - Usually this type of information is not release to someone who is not a technician (or to a consumer) and it is very rare to find enough information to do it yourself. In most cases this information can be found on the internet; however it is not provided directly from the manufacturer. Typically this is something that you want a certified professional to install/remove for you due to safety and liability reasons. They also usually warranty their labor just in case something else may turn out to be the root cause of your initial problem and it does work out better to your advantage. Consider contacting your manufacturer for more details on who in your area can properly repair/install this part. (part usually have a 30 day warranty with tech). I would suggest contacting your manufacturer to provide you a listing of authorized technicians in your area whom may guide you through this process.

Error Code: E3Reason: The voltage is higher for 3 secondsSolution: Check voltageSource: Induction Cooker Error Codes Explained

E5 or E0 means that the stove is getting overheated. You have to reduce the temperature for it to stop. It goes on with few beeps and then stops.

E7 error code definition: "Internal Electronic Temperature sensor is opening circuit or short circuit"Solution: Contact technical supportSource: Induction Cooker Error Codes Explained

e 3 is error because of high voltage may be more than 30 kW at your house......it will not work with it u have to buy a voltage regulator for it........

It is possible that there is fault in the circuit as the drive section seems to fault when the current requirement is high. It is also possible that there is a component possible a semiconductor- MOSFET- that has gone weak during the power outage and so fails .
It is best to have it checked now as it might save a larger expense if the whole unit fails. Also someitmes it can be a silly dry soldering which can be done up immediately. So get support if youa are not able to DIY.

Hi and welcome to FixYa,
I can not insert the symbols here to properly answer your question so, I found the manual and you can read the steps on page 9 here:

http://awadnahas.net/pdf/UserManual/bf7e9e9b-cc9e-46fc-94a7-5965a2d61b18.pdf

This is copy and paste from the manual and the symbols will not come out:

Switching off the child safety device

• Start the hob with ( ' ). Do not set the heat settings . Touch for (Up arrow) 4 seconds. The

symbol ( 0 ) comes on.
• Stop the hob with ( I )

The symbols I typed above are not 100% as they appear in the manual.
Thanks for choosing FixYa,
Kelly

Error Code: E3Reason: The voltage is higher (140V-160V)for 3 secondsSource: Induction Cooker Error Codes Explained

Try
mauritron.com

They have the world's largest library of
owners user instructions operating guides
and
technical repair schematics circuits service manuals

I'm not connected to them, just a satisfied user.
Also if you don't find your item in their listing then ask and they will get it for you

If its a Rangemaster induction cooker, I had the same problem and its caused by a Loose or faulty PT sensor under the glass, you need a qualified engineer to rectify it.

Possible there is short in the oven heater. You will need to check individually the circuit for short or leak into the circuit. Also if the trip is on a ELCB then this is due to an earth leak. Please check if there is leak on the wiring or a possible poor earth/ground connection at the outlet.

Sorry to read about your problem, I hope this helps you out.

stop using and call a service company, before further damage occurs.

I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck

My hob unlocks with that I turn on the hob and the the L appears, then I hold down the lock button until it disappears then I push the STOP/GO button.