Amana Refrigerators - Page 8 - Answered Questions & Fixed Issues

Mechanical failure. You have to replace the filter every three months.

if you removed the inner section of the door for the drying process then it is possible that the door has warped and you have locked it in that shape on installation of the inner section loosen off the screws and twist the door so that it touches all the way around , then retension the screws make adjustments at the hinges after that

Did you check to see if the compressor is running? Did you mess with any of the wiring during your "repair"?

Buy a Frigidaire. We have one and have had no trouble with it.

Amana Water Filters Refrigerator Water Filters Scroll down the above page. Instructions are further down. Video is on the left.

at the back there should be a drip tray if this is full it will leak onto the floor it could be this, it could also be the drain in the fridge is blocked on the back there should be a self made into the back with a hole in it this is to go to the vapure, the part i was on about before, the tank is on top of the pump and its hot so turns the water in to vapour, usually there is not a lot of water but if the pipe becomes blocked it stores the water in the pipe and then lets it go in one full step over flowing the container. to clean the pipe out you can use a flex line or a net curtain rod, push it down and up the hole a few times the blockage will fool to the bottom or come out on the flex.

It depends where the hole is and the accessibility. A certified ac technician would have to do it for you.

Door seals dirty/failing, letting air in and raising the temperature. The "beep" is a warning of that rising temperature. Clean seals thoroughly, spray with silicone and wipe down again. If that doesn't work Google the Manufacturer and enquire about buying a new door seal.

You need to get the model number... look up the DUAL water valves (which seem to be missing) and hook up the water & ice RESPECTIVELY Watch those supplier videos... Those new press connectors are a snap to use (and release)... appliancepartspros Search Over 2 1 Million Appliance Parts partselect PartSelect Appliance Parts and Repair Help repairclinic Appliance Parts Lawn Mower Parts Heating Cooling Parts 365 day returns kit LIKE THIS... (can't tell w/o model number) Amazon com 2181730 Quality Replacement Dual Water Valve Kit for... Carnac the Magnificent

Do you remember how you took them out? It is not usually hard too snap them back together. Just put the support beam back in and the top shelve. Align your baskets in the grooves.

I would think that the part he is ordering would be the main control board otherwise known as the jazz board. They commonly fail but seldom lose the display and usually just stop defrosting the unit. This can be verified by listening closely, and setting the control to zero or the off position and you will still hear the compressor running. Reach up and smack the control and it will go off. part # is WPW10503278 and the only thing I can think of is that he would be ordering a sensor as well. The third part is a mystery to me so update and let us know please!

take it back and never leave the store without testing it

Either the paddle for the ice/water dispenser is stuck or you have a bad microswitch behind the dispenser.
To stop the ice/water from dispensing open the freezer door and press or hold the child lock button down. Once the unit is in child lock mode you can shut the door without energizing the dispenser.
Another option is to remove the upper freezer door hinge cover and disconnect the wire connector up there. This will remove voltage from the dispenser as well. Then either replace the paddle or switch. Sometimes the paddles/switches will get stuck because of splash up from ice dropping in sugary drinks.

You pretty much answered your own question. If the remaining working bulb works in the socket and if the base seems to be not long enough on the replacement bulbs - there is most likely a problem (or by design) - with the bulbs. The best way to be sure is to ensure the correct bulb type - c6, c9 etc. http://www.appliancepartspros.com/whirlpool-light-bulb-8009-ap3607217.html 40 Watt Appliance Bulb If you need further help, reach me via phone at https://www.6ya.com/expert/michael_e7c2c48c6e65f808

Sounds like a problem with defrost system , It could be one of there components , timer, heater, or defrost thermostat. try advancing the timer, down at the lower area behind the grill. with a screw driver by putting it into the dial advance and turn it till it clicks and the unit shuts off. now you should see red glow at bottom of back panel in freezer or here sizzling . if this does not happen then it will be the heater or the thermostat.

Contact the repairclinic.com for tech advice, they are very knowledgeable about these types of problems and what causes them, the service is free and they can sell you the needed parts after you chat with them online.

Check out freezer temp - should be around zero degrees. Fact that ice maker is still working would indicate that the temps are at least about 10 degrees. If the door seals are tight and the self defrosting mechanism is working properly, the unit may be low on refrigerant. I had similar situation where stuff was frozen but my ice cream was mushy even though unit was running 24 hours a day.

Adaptive Defrost Control Board Part Number: AP3109394 MFG Part Number: Made by: Whirlpool

You can seal off those lines going around the door that's called the Yoder Loop. but as far as the class action lawsuit or getting Amana or Whirlpool to pay for the anything good luck. There are very few success stories there.