AOC Televison & Video - Recent Questions, Troubleshooting & Support

This sounds like a common problem on these TVs. Try a factory reset:1. Press and hold "Menu" and "Channel+" on the TV. (do not use the remote)2. Using the other hand, press the Power button.3. *A small screen should appear in the top left part of the screen.4. Using the remote, select "Memory Recall" and Enter.5. Power off and reboot the TV and Computer.6. Run channel auto-scan to regain the picture.If this still does not work, perform steps 1-3, but when you get to step 4, select "EEPROM Init". Then steps 5 and 6 to power it off and back on.

Do a factory reset: Try this: 1. Press and hold "Menu" and "Channel+" on the TV. (do not use the remote) 2. Using the other hand, press the Power button. 3. A small screen should appear in the top left part of the screen. 4. Using the remote, select "Memory Recall" and Enter. 5. Power off and reboot the TV and Computer. 6. Run channel auto-scan to regain the picture.

If the buttons on your AOC 24G2U monitor are no longer functioning as expected, and you can only control the input/source selection, it indicates a possible issue with the monitor's control panel or the firmware. Here are some steps you can try to troubleshoot the problem:

1. Power Cycle: Turn off the monitor and unplug it from the power source. Wait for about 1-2 minutes, then plug it back in and power it on again. This can help reset the monitor's internal settings and may restore the functionality of the buttons.
2. Button Combination Reset: Some monitors have a button combination or sequence that can reset the settings to their factory defaults. Consult the user manual for your AOC 24G2U monitor or visit the manufacturer's website to find the specific button combination for resetting the monitor's settings. Follow the instructions carefully to perform the reset.
3. Firmware Update: Check if there is a firmware update available for your monitor model. Visit the AOC website or contact their customer support to inquire about firmware updates. Updating the monitor's firmware can sometimes resolve issues with the control panel and restore full functionality to the buttons.
4. Physical Inspection: Inspect the buttons on the control panel for any signs of physical damage or debris. Sometimes, dirt or debris can interfere with the proper functioning of the buttons. Use a soft, lint-free cloth to gently clean the buttons and the surrounding area.
5. Contact AOC Support: If the issue persists after attempting the above steps, it's recommended to contact AOC customer support for further assistance. They can provide specific troubleshooting steps or arrange for repair or replacement if necessary.

Please note that the steps provided are general guidelines and the exact steps or options may vary depending on your specific AOC 24G2U monitor model. Always refer to the user manual or contact the manufacturer's customer support for model-specific instructions.

Hi there , sound like it may need output caps

This sounds like a boot log issue, if a new EEPROM can be purchased that should fix the issue, other option is replace the main board

moved you from Computers to TV ( A 2007 MADE TV) now maybe get answers, yah think? sure. I WILL ASSUME CLICKER HAS FRESH BATTERIES AND BRIGHTNESS MOVED MAX AND ANSWER. ALL MODES OF VIDEO DIM, some old TVs do DIM with age, for sure OLD CCFL BACKLAMPED TV OF ANY KIND, THE MANUAL WARNS LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY THAT MEANS CCFL TUBES. INSIDE AND ALL DIM WITH AGE AND MOST THIS OLD ARE EVEN DEAD. CLUE #2 IS IT HAS A CCFL INVERTER BOARD, THIS IS NOT A LED BACKLAMPED TV AT ALL./ ALL ARE DOOMED. (20K HOURS USED AND DIM IT GOES)_ OR WORSE THERE IS YOUR ANSWER AND SAME THING ALL TV. 2000 TO 2010 YEARS WITH ROTTEN CCFL TUBES. BUY LED TV NOT CCFL. OR OLED

use the input button on the TV to get to HDMI 1 then hook the box into that on the back of the TV

A pc tv 32w063 no sound

Make sure that your search is set to include both analog and digital channels. If it still does not find any channels, then it could be a problem with the tuner assembly.

Check the remote control for its infra-red emission. Check it with fresh batteries. If it is found OK, check and replace the infrared sensor inside the TV. If you wish to get some details; check the site linked here. It has details about how to check a remote control; by one among the post. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ If the remote control is found OK; check and replace the infra-red sensor inside the TV. Contact any service technician.

When ubuy a remote it comes w codes..just keep xperimenting

It sounds like it is not seeing any signal. Do you have the input set for the proper type? Air or Cable Check your RF connection to ensure you have a signal coming into your television.

Try unplugging for a bit. Plug in hdmi cord b4 plugging back in.

In the menu system there is a reset (I believe it's all reset, or reset all...something like that) which should fix the issue.If not, leave the TV unplugged for 4 hours and plug it back in then turn it on.

como programo la tele smart aoc para que prenda sola a una cierta hora?