Asko Washing Machines - Answered Questions & Fixed Issues

They never make these things easy. Help in the link https://www.google.com/search?q=Asko+dishwasher+D5634+drain+pump+replacement ..

Question edited for clarity. Duplicated question deleted. Refresh the page to see your question. When a machine stops mid cycle is usually because the pump is jammed with something that was in the wash or the pump has failed. If the board calls for the pump to run and it doesn't within 2 seconds or so, it will stop all actions. You can try a proper Power Reset. Disconnect over night, press and hold the power button for a full minute, then plug is back in. It may also be a Control Board fault. Ideas in the link. https://www.google.com/search?q=Asko+W6424W+washing+machine+froze+mid+cycle+ll+of+the+lights+flashing ..

No wash agitation or spin? try these: WATER PRESSURE SWITCH: This switch keeps your washer from overflowing. It is responsible for shutting off the power to the fill valve and redirects the power to the timer to start the washing machine running once the correct water level has been reached. Meter check ur water pressure switch? You can test it with a meter and with a manual test? ( first locate it in the panel, it has a plastic clear tube hose going into it, remove that tube from its connection, now put another small tube or hose into the slot where it was and have the machine set to wash cycle with water in it. Blow into the other end of the tube. If the machine starts to wash. the pressure switch is more than likely good ( No wash starts - then THE DIAPHRAGM IS BAD AND SWITCH HAS TO BE REPLACED) another test u can do is Remove the hose and submerge in water. Seal one end and blow air into the other end and look for bubbles. Check for an obstruction in the hose as well. Or take the original hose tube and plug one end and blow into it AT the other end, it should be hard and have pressure, if it is easy to blow and u dont feel any pressure and it feels like the air is going out ? Sometimes they get busted open or a pin hole and release air causing the water switch diaphragm to not open. Another test u can make with a multi meter is by testing the prongs individually. # 15,16,17 (don't worry to much bout the numbers IF U GET THEM WRONG) place ur meter prongs on both out side prongs or connectors of the switch. (where the wire plugs into) take note of weather it shows OHMS or infinity ( open or close circuit) ? Now place the meter on the left outside and the middle prong, take note agin what it shows. Now place meter prong on the right outside and the middle prong. Agin take note what reading u get. ( you should actually get a reading of infinity in 1 and a reading of continuity or ohms in the other 2? Now the tricky part. Agin place a small tube or hose into the switch and blow into it, using the meter do the same test agin on all prongs. But now keep the pressure on the switch when u blow into it, in other words use ur tongue on one end of tube to not allow air to escape. When u test it agin now one of the prongs that once read infinity should now show continuity or ohms, and 1 of the other prongs that read ohms should now read infinity or open. . Motor Coupling If the washer won't spin or agitate the motor coupling might have failed. The motor coupling connects the motor to the washer transmission. It is designed to fail if the washer is overloaded in order to protect both the motor and Drive Belt If the washer won't spin or agitate, check the drive belt. If the belt is broken or if it isn't tight on the pulleys the washer won't spin or agitate properly. mode shifter and or Drive Motor If the washer won't spin or agitate the drive motor might be defective. This is not common. Check all of the other related parts to this symptom before replacing the motor. If the motor is visibly burned out or physically damaged, replace it. Stator Assembly If the washer won't spin or agitate the stator assembly might be burned out. The stator is essentially one half of a motor, it interacts with the tub by creating a strong electro-magnet. If the stator burns out the washer won't spin or agitate. Check the stator for continuity. This part is often misdiagnosed. Transmission or clutch assembly not engaging due to going out or slipping. Door or Lid Latch Assembly If the washer won't spin or agitate the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design. Door Lock Motor and Switch Assembly If the washer won't spin or agitate the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design. Motor Control Board If the washer won't spin or agitate the motor control board might be defective. The motor control board provides power to the motor as well as direction and force. If the motor control board is defective the washer may not work at all or function properly. CHECK THE CAM DOGS INSIDE THE AGITATOR, AS THEY WILL HINDER THE AGITATION PROCESS. However in G.E models the cam dogs are replaced with what is called an agitator coupler. (located at bottom of tub) Remember to check the agitator spline as well for worn broken teeth.

dont be afraid to use pressure and lean the screw driver to the left as you pull down on the agitator goodluck

Videos in this link https://www.google.com/search?q=inlet+valve+replacement+ASKO+D5544 Funny plastic clip shown removed in this link https://genuineapplianceparts.com.au/dishwasher-parts/441586-asko-dishwasher-inlet-valve.html ..

turning it off at the power source then back on again after 15 minutes Should be plugged in, possibly under your sink, or if you know what breaker it's on you can turn it off there. Best to you

For most washers, just close the lid. When the washer is unbalanced open the lid, rearrange the clothes and shut the lid. Washer will start spinning again.

Could be cycle timer failure

screw is down inside of top backwards thread then remove agitator

Splashing in the detergent supply drawer. Perfectly normal.

Hello sir madam, I put a detergent on the way this morning in my ASKO 12002 washing machine but IT just got stuck at n ° 4 of its program then did not rinse at n ° 5; then, it did not wring out either at n ° 7, or anything and arrived at 8 ... it therefore goes through the different numbers but without any action ... to remain filled with water in the tank! What should I do, please? I really appreciate my machine which I have had for a long time and would love to have it repaired. Thank you in advance for your information and various tips. And see you soon, I hope. Cordially, Catherine D. BELGIUM

If your dishwasher uses a quick connect hose to the faucet, you can disconnect it while the dishwasher is running ONLY IF the water is shut off and pressure release button is pushed in to release water pressure inside hose. If the dishwasher is calling for water, it will accommodate for a short loss of time. Remember to turn water back on when hoses are reconnected.

Disconnect it from mains supply for 30 minutes to reset the electronics. You should hear the door unlock as you cut power.

Try some WD40 spray on the door and lock. Just a bit. Try closing and opening the door. The machine should be in the <off> position.

It's goosed

Edited text for clarity. Moved Category form Drills to Asko washing machineThat is a power leakage to earth. It is either a fault with the motor or a damaged wire.

test switch-circuit board for short or failure

sadly without being tested we would be throwing out a wild guess not a good fix answer . call a local repair service

ASKO THE DEALER ABOUT IT

The pump may not be working to empty the tub.