Bosch Dishwashers - Page 3 - Recent Questions, Troubleshooting & Support
Turn on dishwasher, goes to
My Bosch SHE4AM16UC was having the same problem of it going from active straight to clean, and there was water in the bottom making me think that there was either a clog or a pump issue. I took my shop vac sucked all the water out of the dishwasher including the down into the drain area for about 3 min until u think all the water is gone in the entire unit. Then I also took off the drain hose that was connected to either your sink or your disposal and held the shop vac over that area for about 5 min to get all the water and hopefully any clog that may be obstructing the drainage. Put the hose back on and hit start and it worked. So for me it was just a clog either deep in the hose or inside the unit. I hope this helps someone. TonyaB
My Bosch dishwasher has a E15 Error.
This is a flood sensor issue rather than a float switch issue. The sensor is in the tray and senses water from dripping hoses or worn pump seals. It doesn't need much water as the sensor is at the lowest point, so it only needs a teaspoon of water. you can check the connections at sensor end and follow it to the control board connector.
My Bosch Dishwasher is displaying an error code E15, what does it mean? An E15 error code indicates that the safety switch has detected water in the base of the dishwasher
. Your leakage protection system has activated.
Videos as well with fixes
https://www.google.com/search?q=bosch+dishwasher+has+a+E15
..
8/21/2022 5:11:35 PM •
Bosch...
•
Answered
on Aug 21, 2022
Dishwasher does not fill with water
Frigidaire dishwashers can lose their pump prime and will not fill with water if there is no priming water in the bottom of the unit. To solve this, add several quarts of water to the unit. Let it settle down in the bottom until it stops going down. Start the washer and you will hear this water pump out of the drain and the unit will now fill with fresh water.
Bosch Dishwasher E01 Code
Two different ideas from Bosch, either control board or heater element, temperature thermistor. As it fails at the rinse stage where the water is hotter, I would check the latter, or just call for service and get it correctly diagnosed and fixed. If you want to try some things, check connections to the main control board and to the heating components.
https://www.google.com/search?q=Bosch+Dishwasher+E01+Code
..
6/7/2022 5:52:54 PM •
Bosch...
•
Answered
on Jun 07, 2022
Doorlatch accidentally locked on open door of Bosch dishwasher model shp65t55uc/02
Here is how to solve this problem. With the door open take a flat screwdriver and pull the small gray latch towards you until it snaps into the open position. There is no electrical connections to this part. It is totally manual. If the small u-shaped trigger is missing then a new part is needed. See the photo below.
6/1/2022 1:45:53 AM •
Bosch...
•
Answered
on Jun 01, 2022
Bosch dishwasher intermittently not completing cycle, not draining
it maybe something as simple as the door opening during the cycle - thus pausing the machine - this can happen when the machines with plastic tubs get hot - the top of the machine flexs a bit and the latch disengages and the machine stops. Next time it does it just try to push the door closed and hit start and see if it picks up where it left off. A stiffener is needed to repair the fault - but we have fixed with shims in a pinch - between the counter top and the dishwasher to minimize the flex
5/19/2022 1:09:50 PM •
Bosch...
•
Answered
on May 19, 2022
Sanitize cycle light will not go off on my Bosch silence 50
The Sanitize Option was not able to be switched off by pressing of buttons on a Bosch SHE863WF6N. Nothing appears in the manual about how to turn it off. (It might be noted that the other options appeared as though they probably could not be toggled either, though this was not thoroughly checked.) At this point, the dishwasher was unplugged (disconnected from the mains) for several minutes. Upon reconnecting the machine power, and though the dishwasher Sanitize option light was still on, it then became possible to turn the Sanitize option light off by simply pressing the Sanitize option button.
4/13/2022 6:10:58 AM •
Bosch...
•
Answered
on Apr 13, 2022
Bosch SHE68M Intermittently Won't Recirc Water During Wash Cycle
1) check that the jets on the ends of the arms are not obstructed 2) Next time you use the machine open the door after a couple of minutes and pour in a litre of water. If the machine wakes OK it means the machine was short of water and it could be that the in-line filter on the water feed pipe to the inlet valve at the back of the machine is clogged. Very easy to check and rectify but it means pulling out the machine and switching the water off. If the filter looks clear it could be the fill valve itself. Another issue can be build up of crud in the fill matrix - remove top and side panel to see this when filling. If there is gunge then switch off, disassemble the matrix and clean out
3/11/2022 8:49:19 PM •
Bosch...
•
Answered
on Mar 11, 2022
Classixx model SMS40C02GB/25. What causes it to stop and turn on 'check water' light?
Sometimes the inlet pipe filter is restricted. Although water flows into the machine it is on a timer and if not enough water enters the machine registers that it is low. To test this start the machine and after a couple of minutes open the door. Add about a litre of water and then close the door. If the machine runs full cycle it's due to either an obstruction in the inlet filter or in the inlet matrix on the left hand side ( remove top and left side panel to see this)
Not finding what you are looking for?