Braun Health & Beauty - Page 5 - Recent Questions, Troubleshooting & Support

Possible bad battery

It is hard to say for sure which component on the circuit board is burned. But, if the shaver will not work after putting the battery in the correct way, it has been damaged beyond repair. It is a little late for this advice but it is always a good idea to note the polarity of the battery before removing the old one(s)

you can look at this sight and look for you model and see a user manual. http://personalcare.manualsonline.com/manuals/mfg/braun/braun_styling_iron_product_list.html

Maybe it's fond of it's self.

Is the Speed Switch not Start->Stop->Pulsator on yours?

Managed to fix it - actually was a 7680. Only do this if you:

1. have a small screwdriver set

2. are handy putting little delicate plastic pieces and springs together again

3. are prepared to face the possibility that you might break the shaver entirely

4. you are out of warranty so you don't care if you invalidate it

THE PROBLEM is caused by a small flat metal assembly that acts as a spring to hold the blue button in place. That is held by 4 small glue posts. The glue breaks down, the flat spring falls out of place and the blue button is no long in the right place.

TO OPEN UP THE SHAVER

a. gently remove the plastic cover around the electrical socket underneath, using a small flathead screwdriver to pry it open

b. the two metallic sides of the shaver can be pulled away starting at the bottom of the shaver

c. uncrew the four screws on the underside of the shaver

d. remove cutter block, battery/lcd block (make sure you don't lose the grommet around the lcd display

e. pull the spring and little plastic latch off the underside of the switch, make sure you remember how to put it back (took me almost 20 mins to figure out how to get that back afterwards)

f. slide the switch all the way up and pull it off the slide - you might need a little gentle force and a flathead screwdriver to coax it off - be careful you don't break anything here

g. remove the trimmer from the rest of the switch

h. put the blue piece back in place (mine had fallen out), then glue the flat metal spring back in place. I smeared brush-on crazy glue on the flat surfaces to hold it in place, I would imagine a four drops of reasonably strong glue on each of the glue posts would work best. Wait for the glue to dry and achieve strength.

i. slide the trimmer back into place, then the plastic latch and spring - this is the tricky part. Make sure the switch can slide on/off in all positions properly.

j. put the display/battery & cutter block back in place. put the back of the shaver on, hold the shaver together with your fingers and test the switch works in all positions without jamming. If so put the four screws back, followed by the metallic sides followed by the plastic cover of the electrical socket.

GOOD LUCK!!

Tadarise 10mg Buy Tadarise 10mg Online, Tadarise 10 mg Reviews

You will need to disassemble the shaver to see if it can simply be put back in place of if parts need replacing. Braun Series 7 Shaver Disassembly Tutorial

You did not include the specific model number of your shaver, so it is difficult to answer for your particular model. Most shavers will unlock by holding in the on/off button for 5 seconds

?ngilizce okumak ve yazmak i?in Google ?eviri'yi kullan?n l?tfen. https://translate.google.com/#auto/tr/Use%20Google%20Translate%20to%20read%20and%20write%20in%20English%2C%20please.

https://www.service.braun.com/product/product.asp?rg=NA&c=US&l=GB&typ=ui&s=&seite=&sString=4243%7CHH%7CHH04%7CH%7CMultipractic+Plus&subgrp=&grp=&frmTyp= Web site says that the product is out of service. There may not be a manual available online. Other model manual online, that might be helpful: https://www2.braunhousehold.com/en/customer-support/instruction-manuals?prd=7862 Contacts in different countries: https://www2.braunhousehold.com/en/customer-support/contact-us

Hello

Remove the electrical cord from the base of the shaver.

Press down and slide off the panel on the front of the shaver.

Remove the two nickel-plated batteries. Use these batteries as a guide to purchase new batteries at a hardware store or home repair store. Recycle the old batteries when finished. (Many hardware and home repair stores have battery-recycling stations.)

Put the new batteries inside the shaver and press gently to pop into place.

Place the front panel back on the shaver and plug the electrical cord into the bottom of the shaver. Connect to an electrical outlet to charge.

THANK YOU FOR VISITING FIXYA

Battery for your model can be found on amazon, take a look here: HQRP 2 Pack Batteries for Braun Flex XP Model 5663 Type 5720 Razor Shaver.... Have a nice day