Brother DCP - Recent Questions, Troubleshooting & Support - Page 6

Clean head aliment sensor

Right side of hean remove upper cover

Turn off printer pressed menu then on press 99 ok

Scanner error check scanner cable and strip

Open front cover press back key replace drum press yes and off on machine

First you need check your ink cover is probably working like open close after that open ink cover and install cartridges slowly

Do not use single paper in paper tray use multi papers and also clean paper feeder

Clean matance box ?? also matance box small switches

First release ink cover door after that install Catradge slowly if problem is still clean Catradge sensor but first check ur ink cover open close is working or not

Unplug the power card pressed menu button and then plug ?? in power cord till display showing matance mode.. After that release menu button use up and down key use up 8 press ok then also use up key press 0 and then use mono button and got purge count use up and down keys press 4 ok 8 ok 2 ok 3 ok purge count 0000 then off and on peinter and enjoy

The printer have its own initialization but seem to fail to complete initialization process. Check and clear the carriage jam, open check for motor failure in the carriage system.

If Brother support told you to take it to a service center, what makes you think Brother support was wrong? Why not take it to a service centre?

http://www.brother.co.uk/g3.cfm/s_page/50630 does not list a DCP 110 printer.
This is the manufacturers website.
I suggest you email their support or call the help number.

You can download it from Brother. Go to this link for your model:
http://welcome.solutions.brother.com/bsc/public/us/us/en/dlf/download_top.html?reg=us&c=us&lang=en&prod=dcp130c_all
and select your Operating System, and Language, and then download and run the software.

did you take the tape off the new cartridge and is the print head burned out for the black? if you installed the diagnostic's on it then run it and see what it says, otherwise expect the print head to be cooked, however it is possible to get a bad ink cartridge try tapping it on your finger and see if ink comes out if it does not then the ink cartridge is dried out or no good, about %15 of print cartridges are bad on just about any brand printer some more than others.

Follow the link below for the user manual
http://www.brother-usa.com/manuals/default.aspx?ProductID=DCP130C&ProductGroupID=5&WT.cg_n=Support&WT.cg_s=Manuals

Please let me know if this helps.
Thank you,
Mark

Remove and clean the pads in the waste ink chamber inside the machine. Then perform the purge reset.

Here is the solution that will reset the count and allow your fully functional toner cartridge (the one the printer tells you is empty) to continue to work.

Open the front cover.
Press options button.
Press the start button.
Press + or up arrow button 10 times.
Press set button.

You have to do this with a long pause or the system will reset and you will have to start over.

Good luck.

Several links with possibities: http://www.fixya.com/support/t3704926-brother_mfc8640d_a6_error https://www.justanswer.com/printers/5b111-brother-dcp-8040-showing-machine-error-6a-solu.html https://www.manualslib.com/manual/549919/Brother-Dcp-8040-B-W-Laser-All-In-One.html?page=210 Quoting from manualslib.com: 6A (Heater does not reach 60°C within 11 sec.) Heater warming-up timeout error. Thermistor ASSY • Halogen lamp

Hi, Try to reset Purge, it just might help. 1. press buttons OK, Menu, Mono Start one by one, followed by up arrow key four times. this should all be done as short a time as possible, around 3 seconds. 2. enter maintenance mode 80 by pressing the up/down arrow key and set key to select numbers 8 and 0 3. press blue MONO start button to select PURGE which requires it to be pressed a number of times before PURGE appears on the LCD screen of the printer 4. then use the up'down key and OK button to enter the reset code 2, 7, 8 and 3 keys to reset the counter : Note this does not overwrite the number next to PURGE on the LCD screen but once the last number is added it gets reset to 0000 5. press Stop/Exit key to go to root of maintenance mode 6. enter 9,9 to exit maintenance mode Clean unable 46 error on dcp 135c brother printer