Brother Sewing Machines - Page 8 - Recent Questions, Troubleshooting & Support

DOUBTFUL THAT IT WILL DO HEAVY LEATHER PERHAPS GLOVE THIN STUFF

Am looking for a part for my brother compal opus model 845 .what it is the part is called electrial plug replacement pin need a set of 2 .i have a phot of part but no part number .i cant seem to send you the phot, regards julie donnelly

I have the same machine and a copy of the original manual. Happy to send a copy of it. I need a belt...know where I can find it?

Gargle it in google; brother ax-350 typewriter manual

$12 https://www.shopgoodwill.com/Item/55875836 https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk007ZkMhoUwSGXuiNDDVPVpBojYD8w%3A1615145532430&ei=PCpFYNDnGYG5ggeqy6fYCA&q=Brother+sewing+machine+model+Opus+821A+for+sale

Brother Collectible Sewing Machines for sale ' eBay

www.ebay.ca > ... > Brother Collectible Sewing Machines

Results 1 - 48 of 204 - Brother Charger 651 Vintage Heavy Duty Sewing Machine Manual Blue ... Brother OPUS 1351 - VTG Made in Japan Sewing Machine. ..

Check the cotton tension.

Change measurements from mm to inches

1. Turn on the sewing machine. The LCD comes on.
2. Press. on the operation panel. The settings screen appears.
3. Switch screens using or. until the below screen is appears.
4. Press. to switch between mm/inch.
5. Press.

Change measurements from mm to inches - Brother

Information on your touch screen, it is a known issue. Links to parts suppliers. https://www.google.com/search?q=brother+super+ace+11+sewing+machine+sensor+panel ..

Hi....I also kept getting the check and rethread upper thread message, I\'d sew about 15 stitches and it\'d stop. Here\'s what I did. On the left of the machine, in the back there is a screw....loosen that screw, take cover off, then lift straigt up and out on the cover that has the 3 on it in your threading seqence. Next, I started inspecting and cleaning the thread route from top to bottom. Lo and behold....I get to the place where you come down the front of the machine and turn to go back up and I spot a little slit in the plastic piece so, when I was threading the machine I guess I was pulling it to far to the left causing it to wear a little slit in that piece....so, I finished cutting it off with a utility knife, used an emery board to smooth it down, put the covers back on and it works GREAT!!!! Who would\'ve ever that it\'d be so easy and save me a bunch of money!!! I sure hope this helps someone.

Replacing the belt is a cheap and easy fix if it is the belt slipping. however, the fact is stops at the same place makes that that the machine needs servicing and re-timing.

Empisal has been the top supplier of sewing equipment for over two decades. So you can never wrong with any of their machines. Whether you need a sewing machine, overlocker or steam press, Empisal should be your sewing equipment choice the 760d is nit that old and it work great for all your basic need/

https://www.sewingonline.co.uk/library/BROTHER-VX-970.html

Request the manual from Brother

1. Button failure 2. Circuit failure

Hi Emily: Google this brother CS6000i Computerized Sewing Machine manual Then take your pick.

Be sure to select a compatible stitch e.g 0, 1, 4, 37, 38, or 40. See owners manual. Note reverse stitch not supported for all selections.

Try rotating hand wheel manually after stitch selection to check for interference.

personally i would take to a local repair shop. there should never be parts falling out

It's hard to give an idea about it. ch

Brother might be able to furnish one.

Request the manual from Brother.