Blenders - Page 2 - Recent Questions, Troubleshooting & Support

"Elite Cosine" :>D I changed it for you and added '(what it is)'. Question moved from Elite Televisions. There may be a thermal fuse. But this is junk made in China. A complete new one will cost you $40 at BestBuy. If you can find a thermal fuse, you can replace it as a generic component by the details on it. https://www.google.com/search?q=Elite+Cosine+EPB1800+fuse ..

It makes cold soups like Gazpacho and Vichyssoise, so make sure the heating / cooking function is set. If it is, ask Russel Hobbs where your local service centre is to diagnose and replace the element. https://www.google.com/search?q=Russell+Hobbs+soup+maker ..

The nylon coupling is either cracked or missing. A flat key extends from the motor shaft and locks into the extension like a paddle in order to move the blades. If you can not find the insert, this style of interlocking is common mechanical design. There are sometimes a spring clip the paddle interlocks with. The nylon insert locks into the blade rod mechanism. I suppose the nylon insert is designed as a replacement part rather than replace the entire blade extension

That sounds like it is overheating. Does the red power light flash before it powers itself off? Units like this with an enclosed motor often have an internal fan as part of the motor and vents on the base to drive out the heat. Various other ideas here and a link to Ninja Kitchen Support https://www.google.com/search?q=ninja+blender+starts+at+low+power+and+then+stops+when+increasing+the+power ..

Me too!

This looks Spammy, but the answer is Vitamix.Yogurt or liquid first and fruit on top and let rip!A blender is the only machine in your kitchen that can produce a beverage from chunks of ice and fruit in less than 60 seconds. And no other blender we've tested since 2012 can reliably make silky soups, spoon-thick smoothies, and stable emulsifications like the Vitamix 5200. Yes, this model is pricey, but we think its powerful motor, nuanced controls, and long-lasting reliability make it worth the investment...

Question edited for clarity. Question moved from Firearms Optics. Is it Australian? We don't know it in North America. This link may work better for you than me in Canada! https://www.google.com/search?q=ronson+hand+blender+parts+list ..

I need the plastic piece that goes in the middle of the lid on a bone appetite blender serial num. BAPBL010

It can only be three things Switch Motor Broken wire (unlikely) How good are you with a screwdriver and a digital multimeter at testing components? https://www.google.com/search?q=Kitchen+Aid+blender%2C+Model+KSB5WH1 ..

Question edited for clarity and for his correct first name. You need the model number, but spares are available. https://www.google.com/search?q=Wolfgang+Puck+commercial+blender+replacement+blade ..

@DeEdra you resurrected a post from 10 years ago! :>D https://www.google.com/search?q=Food+Network+replacement+parts ..

Question moved to blenders. " Overly "?? Do you mean Oster by any chance? You you can replace blades. https://www.google.com/search?q=Overly+blade+replacement+in+blender ..

I was just able to fix mine. You'll need the following: two wrenches (almost any type), steel wool, and vegetable oil.

1. Clamp the hexagonal nut inside the bottom of the pitcher with one wrench and place the jaws of the other wrench between the "spokes" of the wheel at the outside bottom of the pitcher.
2. Turn either counter-clockwise until the hex nut comes off. At this point, you should be able to pull the bottom piece out from the bottom. Pay attention to the order and orientation of the parts inside the pitcher as they may fall out now.
3. Dry off the shaft and rub it with some ordinary steel wool (think SOS pads).
4. Twist a small amount of the steel wool and run it back and forth through the hole the shaft goes through.
5. Wipe both clean with a clean cloth or napkin.
6. Rub a little vegetable oil on the shaft.
7. Place the shaft back in the hole and test the movement. It should be like new again.
8. Reassemble the blender.

Hope this helps,

John

To open the motor casing of a Breville BLR50S Blender, you will need a screwdriver with a long and narrow shaft that can fit into the recesses where the securing screws are located. A precision screwdriver set with interchangeable bits may work well for this purpose, as it typically includes a range of sizes and shapes of screwdriver tips that can be swapped out as needed.

Alternatively, you may be able to find a specialized tool that is specifically designed for this purpose, such as a long-shafted screwdriver or a tool with a flexible extension that can reach into tight spaces. It may be helpful to consult the user manual or contact Breville customer support for more information on the specific tools needed to open the motor casing of your blender

At 600W and Voltage(rms) of 240V gives Current(rms) of 2.5amps, so max current would be about 1.5x2.5 or 3.75amps. A 5amp fuse should suffice in that case.

My Blender Model number KSB560MCO does not run. When try to blend all of red lights come one and they blink and move around. Any suggestions what could be wrong? Appreciate any help.
Thanks

It is possible that the charger for your Farberware blender is not functioning correctly. I suggest contacting Farberware for a replacement charger or repair instructions, as this is likely to be the best way to resolve the issue.

Are you blending ice cubes? They are NOISY. Blenders are generally noisy!

clean and tighten blade --if still leaks replace seal or need replacement base if damaged